May 3, 2023
…distance from the centre of the servo horn to the rod end ball can be adjusted steplessly from 19mm to 23mm with just one screw. You can instantly adjust the lever ratio according to the servo speed and counter timing. SE (shiny edge) processing is applied to each edge of the 2 separate bodies for improved looks. The line-up includes two types of serrations, 25T (for servos such as Futaba and Rêve D) and 23T (for servos such as Sanwa and KO) so that you can choose according to the servo manufacturer you are using. Source: Rêve D [teamreved.com] FacebookTwitter…
July 6, 2022
Radtec have released their new steering servo horn with an adjustable length of 17, 18, 19 & 20mm. Sporting laser engraved marking for easily identifying the setting, it has a clamp type design for reduced play on the spline. Available in a 23T version that is compatible with KO/Sanwa and in 25T which is compatible with Futaba/Power HD & others servo. Source: Radtec [radtec-rc.com] FacebookTwitter…
June 22, 2022
This lightweight and super rigid split servo horn from Rêve D can adjust the distance from the centre of the servo horn to the rod end ball steplessly from 19mm to 23mm with just one screw. It is possible to instantly adjust the lever ratio according to the servo speed and counter timing. There are two types of spline fitting, 25T (for servos such as Futaba and Rêve D) and 23T (for servos such as Sanwa and KO) so that you can choose according to the servo manufacturer you are using. A secure clamp method is used for mounting the…
October 5, 2021
Ruddog Products’ new 23 turn 3-Slot Cup motor is an ideal low-budget choice for endurance or club racing. The Cup motor is a perfect match for the ESCs included in entry-level on-road and off-road kits, and a ball bearing in the front end bell increases the efficiency and lifetime. A perfect motor for your first racing experience. Source: Ruddog Products [ruddog.eu] FacebookTwitter…
July 1, 2021
…the steering and creates a finer resolution. You are able to set any height between 16-19mm without the need to switch any plates or parts of the horn, which makes it a quick setup change option by sliding the ball stud up or down. The slightly bulkier arm design adds some extra strength and reliability. For the perfect ‘play free fit’ with the servo spline the design utilise a clamping design. Available in two versions, 23T & 25T, the servo arm is machined from high quality black anodised aluminium with silver edges and laser engraved logo. Source: MXLR [maexler.com] FacebookTwitter…
May 14, 2021
From Creation Model for the Infinity IF18-2 is this new front upper arm holder. Machined from 7075 aluminium, the strength and rigidity is increased, providing higher corner speed in certain conditions. The black anodised finish complete with Infinity logo also adds a cool look to your car. Sold as a complete set with a full range of inserts and mounting hardware. Also for the IF18-2 is this new lineup of pinion gears with hard coated 7075 aluminium material. Offered in all sizes, 18T, 19T, 20T, 23T, 24T & 25T allowing you to fine tune the gear ratio to the engine…
February 5, 2021
T-Works have introduced these adjustable clamping servo horns. Machined from 7075-T6 aluminium, and black anodised, they are available in both 23T and 25T spline versions and are extra secure thanks to the clamping screw. Supplied with A and B non threaded inserts that offer a range of positions from 17mm to 20mm, there are also two optional sets of inserts. The optional non threaded C, D & E inserts, combined with the standard A & B inserts, offer mounting positions in 0.5mm increments from the pivot point from 16.5mm to 20.5mm while the optional threaded inserts A, B, C, D…
December 29, 2020
LC Racing have produced this +2mm aluminium servo arm for their LC12B1 1/12 buggy and 1/14 EMB series vehicles. The longer servo arm gives a faster steering response and the material used improves strength. Red anodised, it features a 23T spline. Source: LC Racing [lcracing.net] FacebookTwitter…
