Red RC » Factory Team

February 19, 2026

Factory Team RC10B7 67mm Universal Driveshaft Set

Factory Team, the option parts & accessories brand of Team Associated has added this new 67mm universal driveshaft set set for the RC10B7 1:10 2WD Buggy. The shafts are ideal for those that have the -4mm hubs with the 81mm arms and want to try universal driveshafts in their vehicles. These driveshafts can also be used for times where the 69mm universal driveshafts are too long for your specific configuration.

Source: Associated [associatedelectrics.com]

February 4, 2026

Factory Team RC10T7 | SC7 Chassis Protectors

Factory Team, the option parts & accessories brand of Team Associated, has introduced chassis protectors for the RC10T7 Stadium Truck and RC10SC7 Short Course Truck. These protectors are precisely cut to fit the main chassis and have a design very similar to other Team Associated RC10 chassis protectors. The protector ensures minimal damage going over rough terrain and also has the benefit of keeping your screw heads clean.

Source: Associated [associatedelectrics.com]

November 8, 2025

Factory Team Onroad Tools

Team Associated’s option parts & accessories brand Factory Team has introduced a number of new tools intended for onroad use. The new line includes an onroad wheel arch cutout tool for racing out the wheel cutouts on your body and ensure it is centred with the tyre. A new chassis balancing tool makes balancing your car easy, simply rest your vehicle on the balancing tool using the two holes in the chassis (one on the front, one on the rear). A stepped ride height gauge allows for easy ride height adjustment readings in 0.2mm increments starting from 3mm and ending at 7mm. Finally there is the 10mm droop gauge support blocks are machined to tight tolerances to allow for very precise and repeatable droop measurements. View more images here

January 26, 2022

Associated FT Lockout slipper clutch

Get the most out of your No Prep Drag Cars with Team Associated’s new FT Lockout slipper clutch. It dynamically and independently controls the amount of slip created during launch and when down the track at speed. Lockout combinations are unlimited, depending on track conditions, amount of power, chassis setup, and throttle application.

View the complete lockout slipper clutch set here

January 24, 2022

Factory Team parts for DR10, SR10, RB10 & Pro2 SC10

Associated release these new Factory Team parts, designed to add adjustability and increase the durability of your Team Associated car. Highly adjustable C and D arm mounts as well as rear hubs allow for fine tuning toe, anti-squat and roll centres to make your vehicle perform as desired on any surface you drive. All of these parts fit: the Pro2 SC10, DR10 RTR, DR10 Reakt Pro Mod RTR, SR10 RTR and RB10 RTR.

View the new products here

December 15, 2021

Factory Team titanium 1/8th turnbuckles

New Factory Team titanium 1/8th turnbuckles add bling and durability at an affordable cost. Each part is made from high quality titanium and is a direct replacement to the stock steel turnbuckle. The 5x44mm length turnbuckle is a replacement for the existing 5x38mm length steel turnbuckle. The increased thread engagement adds extra durability. Also available is 4x50mm, 4x85mm and 5x80mm.

View the different turnbuckles here

December 8, 2021

Factory Team 1/8th aluminium pinion gears

Team Associated’s Factory Team brand has released a line of aluminium pinion gears for 1/8th scale. The Mod 1 pinion gears are made from hard-anodised 7075 aluminium and offer a lighter rotating mass over a steel gear. Only to be used with plastic spur gears the new line up includes a 15T, 16T and a 17T version.

Source: Associated [associatedelectrics.com]

October 11, 2021

Factory Team B6.3 +3mm bellcranks

Team Associated’s new Factory Team +3mm bellcranks allow B6.3 racers to tune the caster with 0 and 2.5 deg. inserts and still minimise bump steer. On high-traction tracks, the pro drivers have gained cornering speed by reducing caster from the kit 5 deg. inserts down to 0 or 2.5 deg. Unfortunately, the 0 or 2.5 deg. caster inserts raise the outer steering block ball, creating un-wanted bump steer, which affects wheel angle as the car leans. Their solution has the +3mm raised bellcrank sets counteract the adjustment and help keep your steering angles consistent through the entire suspension travel. This combination makes the cars and trucks corner faster, while also maintaining predictable handling. Made from durable CNC aluminium they are available in both blue and black anodised finishes.

Source: Associated [associatedelectrics.com]