New from King Headz for the Losi Ten SCTE is this steering top plate which has been CNC machined from 7075 aircraft grade aluminium. Black anodized it is designed to increase the rigidity between the top plate and the front shock tower. The upper shock tower bolts screw into the upper plate and will eliminate the chance of the upper plate screws being pulled out of the bulkhead in a bad crash.
Source: King Headz [kingheads.com]
King Headz have released this LCG aluminium motor mount for the Slash 4×4. CNC machined from 7075 grade aluminium and anodized black, it replaces the stock plastic motor mount. This mount will directly work with either the slipper or center diff and was designed to use he included 10X19X5 bearings which are much stronger than the stock 10X15X4 bearing.
Source: King Headz [kingheads.com]
This new MBX-6 toe-in plate from King Headz is CNC machined from 7075 aircraft grade aluminium and black anodized. Designed to increase rigidity and add strength, it will allow you to make 6 different toe/anti squat adjustments. By changing and flipping the inserts you can adjust 6 different combination’s from 2.5, 2.75 and 3 degree of toe-in with either zero degree of anti squat or one degree of anti squat.
Source: King Headz [kingheads.com]
King Headz have released a whole range of products for the new Serpent S811. First to get their attention are the front and rear shock towers which have been CNC machined from 7075 aircraft grade aluminium and black anodized. These are designed to increase rigidity and add strength. They have also produced a 1-3 degree anti-squat plate which too has been CNC machined from 7075 aircraft grade aluminum and also black anodized. These are designed to increase rigidity and add strength and use the factory inserts. Finally there are two type of clutch shoes, machined from 7075 grade aluminium and also 6061 grade aluminum. Sold in sets of 4 shoes.
King Headz have released this Slash 4×4 aluminium motor mount. CNC machined from 7075 grade aluminium it directly replaces the standard plastic motor mount. This mount was designed to use a 10X19X5 bearing which is much stronger then the stock 10X15X4 bearing. The photo shows a prototype with the final version being black anodised.
Source: King Headz [kingheads.com]
New from King Headz are these 17mm closed flanged wheel nuts. CNC machined from 7075 aircraft grade aluminium, they are anodized in either purple or green and are available in either fine or coarse thread versions. These closed nuts are designed to minimize the amount of dirt that gets into the axle and the fine threaded versions will fit Losi, Xray, Kyosho, Hot Bodies, Mugen, Associated or any other M12 X 1.0 hub, while the coarse threaded versions fit the Jammin, OFNA or other M12 x 1.25 hubs. Sold in a set of 4.
Source: King Headz [kingheads.com]
New from King Headz is this Mugen MBX-6 rear toe-in plate. CNC machined from 7075 aircraft grade aluminium and black anodised, it has been designed to increase rigidity and add strength. This toe-in plate will allow you to make 6 different toe/anti squat adjustments simply by changing and flipping the pivot pin inserts giving you 6 different combinations from 2.5, 2.75 and 3 degree of toe-in with either zero degree of anti squat or one degree of anti squat.
Source: King Headz [kingheads.com]
New for the Losi 8ight 2.0 and 8ight-T 2.0 are these front caster blocks which have been CNC machined from 7075 aircraft grade aluminium and anodized. These blocks will allow you to adjust caster on each wheel independent from the other wheel by simply loosening two bolts, rotating the block and then re-tightening the bolts. There are indexing holes and a provided gauge to let you adjust the block from 5 degree of additional positive caster from the stock Losi block all the way to 5 degree of negative caster in 2 1/2 degree increments. These are also designed to increase rigidity, add strength and improve durability.
Source: King Headz [kingheads.com]
