Red RC

September 19, 2020

Pro-Line Axis body shells for MBX8, 8ight-X & RC8B3.2

As teased earlier in the week, Pro-Line have today released full details on the new Axis bodies for Mugen MBX8, TLR 8ight-X and Associated RC8B3.2. Designed with the latest in CAD technology, the Axis features a super low-slung design with sharp lines throughout giving it an unmistakable look on the track. The Axis is a cab-forward design that provides enhanced steering response while the small side fins balance out the rear of the car with ideal side-bite. The rear of the Axis body has the right amount of clearance for the nitro engine and fits the chassis and bulkhead shape of your race buggy perfectly. To run the Axis body on the EP version of the Mugen or Associated, the battery must be no taller than 39mm due to the low-slung nature of the Axis side pods.

View all the images here

September 18, 2020

Infinity small-parts box & case sets

New from Creation Model, comes their Infinity small parts cases and case sets. Coming in three different sets, there is the large hard outer case that comes with the 8 of the smaller boxes, each with 8 compartments, and a set of label stickers for easy identification of stored parts. The second version is similar but only comes with 4 of the small-parts boxes, leaving room in the large box for outer larger parts or tools. Finally you can get a set of 8 small-parts boxes, without the larger outer case but with the labels, perfect for storing small parts such as screws, washers and bearings.

View more photos here

September 18, 2020

MiBorg Sakura D5S rear RCV driveshafts

Coming from MiBorg and made for the 3Racing Sakura D5S drift chassis are these new rear RCV driveshafts. Utilising the design of full-scale cars the driveshafts use steel balls instead of cross pins to drive the wheel axle, which results in less vibration even at high steering angles. This leads to a more predictable handling, higher corner speeds and less tyre wear. In addition the wheel axles allow the use of standard thickness bearings while lighter, pin-less wheel hex adapters reduce overall weight.

Source: MiBorg [miborg-rc.com]

September 18, 2020

2020 GenevaModelCars Series Rd4 – Report

The fourth round of the GenevaModelCars Series 2020 was held recently at the GEMC track in Meyrin, Geneva. With 47 drivers attending in three classes, Touring 13.5T boosted, FWD 17.5 zero timing and Formula 21.5T zero timing all run under perfect weather conditions. The layout chosen for the this round was challenging, as it was both technical and fast at the same time. In the Touring 13.5T boosted class, that is run on Hudy A1-36 spec tyres and without traction compound, Xavier Deparde (Xray) secured the pole position followed by Bastien De Marco (Awesomatix) and Alexis Banderier (Awesomatix). After three entertaining A-mains, Xavier took the overall win, in front of Bastien and Sébastien Leuenberger (Xray).

Continue reading the report here

September 18, 2020

T-Works TC-01 spur gear adaptor & suspension balls

T-Works continue to release new parts for the Tamiya TC-01 with the new parts focussed on shedding weight where possible. First up is the spur gear adaptor, which has been made from hard coated 7075 T6 aluminium, the new material along with the minimal design, help to bring the weight down from 7.1g to 2.1g. Next up is the new suspension balls, again from the same material, the weight saving is 4 grams (8 pieces) over the standard parts. Finally the 24 piece ball end set, again made from hard coated high quality aluminium, helps in reducing the weight from 27.5g to just 7.3g, which when you combine it with the other two new items gives you a total weight saving of nearly 30grams.

View the other new parts here

September 18, 2020

2020 Kinwald Klassic – Cancelled

Hobby Action RC Raceway in Chandler Arizona got in touch to let us know the disappointing news that the 2020 BKlassic has had to be cancelled. You can read the announcement here:

Hello everyone, 2020 has been a crazy time in the world and the RC industry has had to make adjustments on the fly. As you all know the Covid-19 virus has caused us to make some difficult decisions this year and we are at that point again. As of September 17, 2020, the State of Arizona is classified in the “Moderate” zone for the potential community spread, under this level the Arizona Department of Health Services restricts gatherings on indoor assembly. With the current recommended limitation on public gatherings, we have made the difficult decision to cancel the 2020 Kinwald Klassic scheduled for October 17-18, 2020. It is an honor to for Hobby Action RC Raceway to host this event and we will again honor Brian in 2021. Thank you to all those that support us and our hobby. LT

September 18, 2020

Kyosho Mini-Z 4×4 Jeep Wrangler Unlimited Rubicon

Having been hyped on social media for the last few days, Kyosho have just dropped the all new Mini-Z Jeep Wrangler Unlimited Rubicon. This sweet looking crawler uses an all new chassis with steel ladder frame and multi-link rigid-axle suspension. Featuring solid front and rear axles, the ring and pinion gears, in addition to other gears and components, feature metal construction to withstand the heavy loads under the toughest driving conditions. This car comes specced out with steel links and ball ends, coil over type shock absorbers, slipper clutch, an all new gearbox that features moulded covers and includes 6 pinion gears that allow adjustment from ultra-low gearing for steep terrain, through to high-speed gearing for smooth running on flat roads. The car is also full ball raced, factory installed to ensure the smoothest most efficient operation possible.

View more details & images here

September 18, 2020

Rebellion RC MMX body distance system

Similar to the body distance system released yesterday by RebellionRC yesterday, this new version is specific to the Awesomatix MMX. Incorporated into new steering arms, its adjustable design makes it possible to fine-tune the mounting height of the body. Because the body no longer moves up and down with the chassis you can position the body lower than ever before, which in turn improves aerodynamics. For a perfect fit on the knuckle they have used special tools to provide the highest precision, playfree and still easy to disassemble without tons of force.

View the mounted system here