Red RC » JConcepts

May 10, 2013

JConcepts Associated front axles for 12mm hex

One of the best upgrades you can make to the Team Associated line of vehicles is a conversion to 12mm hex wheels. JConcepts has been on top of this conversion since its introduction with hex adapters and Mono wheels. A critical point of the conversion revolves around the front axle and surrounding geometry. Within the steering block the space is very tight and especially between the 2 front bearings where the front axles rests between the bearing bores in 1 plane and the king pin in the perpendicular plane. The JConcepts front axle design is based around high-grade titanium construction, an outer bearing crush step and an inner 4-40 locknut for security. The design eliminates c-clips, screws and other items which are hard to detect of issues which limit performance. Available or the B4.2, T4.2 and SC10, this free spinning design includes axles, 4-40 mini lock-nuts, thin axle shims, decal and assembly instructions.

View the other axle sets here

May 8, 2013

JConcepts Reedy Sonic aluminium timing cover

JConcepts introduces an all new aluminium timing cover accessory for the Reedy Sonic motor. The aluminium acts as an additional heat sink transferring heat to an additional surface spreading the heat out over more area. The timing cover also has increased depth which allows more sensor wire plug protection in the event of a crash or collision. The timing cover is CNC machined, available in blue and black colors and includes upgraded hardware for installation. In addition, each cover also includes a molded sensor wire holder and hardware which routes wires in the up position which decreases possible wire snags or drop-outs which lead to unfinished races. Available in anodised blue or black.

View the unmounted set here

May 7, 2013

JConcepts 10th anniversary limited edition T-shirt

JConcepts celebrates their 10th anniversary with the release of a new limited edition T-shirt. From the prototype B4 Illuzion body and BJ4 competition 4wd buggy debut at the 2003 IFMAR Worlds all the way to the recent racing success during the 2013 Cactus Classic, JConcepts has transitioned throughout the years and ascended through the industry placing itself among the elite. The front of the new racing shirt showcases the most current JConcepts.net logo along with striker imagery, a large arrow which signifies moving forward with a bold 10 making the anniversary statement. The rear consists of a collage of championships and accomplishments which have been of great importance during an amazing 10 year run.

View the shirt designs here

April 27, 2013

JConcepts Satellite tire gluing rubber bands

JConcepts has reinvented the tire mounting rubber band. A uniquely molded design, specifically developed for tire mounting, the rubber band is produced in a high-elasticity material capable of stretching to a full assortment of different sized tires. Finely detailed array of handles are designed to ergonomically conform to your fingers so the user can deftly adjust the rubber band to the sidewall of each tire to apply the pressure where it is needed. The Satellite rubber bands are available in blue and black colors and will include 4 bands per package.

Source: JConcepts [jconcepts.net]

April 24, 2013

JConcepts RC8.2 Silencer body

Seen first at the Worlds in Argentina and then used to win this year’s DNC, JConcepts have finally released the the Silencer for the RC8.2, a brand-new, ground up design which has new elements created for the highest speed circuits. A narrowed, Finnisher stance cockpit allows more fuel tank access a smoother high-speed transition and increased flow around the engine heat-sink. A deep recess around the heat-sink area with dual channeling out the rear provides air escape along with rear-end stability, while the Silencer side-pods have a clipped rear-end, narrowing the rear by angling just in front of the rear tires. The extended runner features are placed on the rear-end of the body enhancing the force placed on the rear pods during high-speed acceleration. The main pods are heavily chamfered and a more heat-shrink design over the pipe, fuel tank and electrical / linkage make up the main pods. The end result has the body looking extremely low-profile with heavy JConcepts edginess and appeal. The Silencer is capped off with a cock-pit “shark fin” for more high-speed tracking stability and increased roof stiffness.

View more images of the Silencer here

April 23, 2013

JConcepts TLR22 7″ Hi-Clearance rear wing

JConcepts TLR22 7" Hi-Clearance rear wing

JConcepts has released their new 7″ Hi-Clearance rear wing for the TLR22. A slightly wider base gives the wing a larger surface area which allows more stability during low and high speeds which provide some much needed grip in tricky situations. The Hi-Clearance sections near the end plates still allow maximum suspension compression and tire expansion.

Source: JConcepts [jconcepts.net]

April 3, 2013

JConcepts off-road wing buttons

New from JConcepts come aluminium wing buttons for 1/8th off-road vehicles. Specially designed for all screw-in wing mounts the machined aluminium design with durable outer rim and stylish hex design offers a bit more security over traditional plastic wing buttons. The buttons incorporate through-holes and notched hexes which make it light-weight and strong in all the important areas. The attachment area has an already built-in countersunk feature which allows for the cleanest assembly possible and the buttons are available in blue and black colour.

Click here to view the colour variant

April 1, 2013

JConcepts Finnisher body for XB4

JConcepts have released a Finnisher body for the new Xray XB4. Increased windshield angle provides a steady force upfront during mid-flight wind gusts on large jumps. Forward cab placement changes performance / visible bias which helps steering rotation in low traction corners. The side-pods have been simplified and JC chamfered to remove unwanted changes in height to neutralize the at-speed handling. The chassis to body fit has been tightened up which eliminates empty voids that contribute to mid-flight directional changes. The rear of the cab has a new step feature which allows the placement of a secondary side window and also a louver which can be trimmed to allow air to escape at the top of the body. In addition to the newly designed body, JConcepts has included 2 of the latest 6.5″ wide Hi-Clearance rear wings.

View more images of the body here