Red RC » RC Maker

October 11, 2017

RC Maker long reach touring car ride height gauge

New from RC Maker is a simplified ride height gauge for touring cars with longer platforms. Outdoor racing with carbon chassis can lead to excessive chassis wear in the exact spots which drivers measure the ride height from. The increased 20mm length of the platforms allows the gauge to reach a more inner, unworn part of the chassis. This gives a much more accurate reading on the ride height, noting the difference between measurements can be from 0.2mm – 1mm depending on how worn the chassis is. The gauge of six platforms ranging from 5mm to 6mm in 0.2mm increments suits all racing conditions with fine tunability. It features a lightweight 7075 aluminium construction with black anodising and white laser etched numbers and logo.

View another image here

October 5, 2017

RC Maker Digital Camber, Toe & Caster setup gauges

New from RC Maker are an industry first line of digital setup gauges for 1/10th EP and GP Touring Cars. The first introductions to the line are two digital gauges, one for conventional touring cars which digitally measures camber and rear toe. This is currently being debuted by Ronald Volker and Yukijiro Umino at IIC in Las Vegas. The second is for Awesomatix Touring Cars which digitally measures the front and rear caster. Consisting of an Aluminium and Carbon Fibre construction, they are built to very tight tolerances accurate to within 0.01 degrees over a 4-degree range. This ensures precise and replicable camber, toe and caster adjustments. The gauge itself features a backlit screen with big numbers for easy viewing in day and night, as well as “auto off” and “zero” functions to be able to zero to your setup board surface no matter what angle it’s on. It also features very easily replaceable AAA batteries and comes with a velvet storage pouch to keep it looking and functioning like new.

View more images here

September 27, 2017

RC Maker Awesomatix suspension ball wrench

New from RC Maker is this suspension ball wrench, which holds the AT21 and AT21S-0.5 lower suspension balls on Awesomatix touring cars. Until now, the plastic ball cup prevented any tool being able to lock onto the hex in order to hold the ball whilst tightening and loosening. These balls are required to be removed whenever changing roll centre or replacing the main chassis. It is made from thin, but very stiff and durable carbon fibre and is available now.

View an image of the tool at work here

September 11, 2017

RC Maker A800X Med Flex Link

RC Maker’s Med Flex Link is a custom built, machined ball link system that provides the front or rear of the A800X touring car with a medium flex option. It allows the bulkheads to flex independently but not together, bracing the front and/or rear of the topdeck under acceleration and braking, yet still allowing it to move sideways in cornering. This provides increased forward traction and stability when used at the rear, and increased braking grip and turn in when used at the front. It also features an integrated belt tensioning system, allowing to run the belts looser for less rolling resistance, whilst still maintaining longevity and reliability. Thee links have all individually been custom machined and fitted to the car to ensure a precision fit and smooth action. They work with both the C27X standard top deck and the VTD vertical top deck. However, they will only provide a substantial handling effect when the braces on the VTD are cut, to allow the flex link to work.

View another image here

August 17, 2017

RC Maker A800X bellcrank steering limiters

New from RC Maker are bellcrank steering limiter plates for the Awesomatix A800X touring car. They adjust the amount of steering lock by creating a hard stopper for the bellcrank arms, unlike just using the servo end point as a limiter. This prevents unwanted wheel vibrations which scrub corner speed, and cause strain on the servo. Consisting of an asymmetrical design, each plate can be flipped allowing 4 different steering lock angles all the way from 23 to 33 degrees. They are durable and have minimal impact on the cars flex, whilst keeping the steering posts aligned under cornering forces.

View another image here

July 25, 2017

RC Maker Awesomatix LS1/LS2 Ackermann plates

New from RC Maker are graphite Ackermann plates for the LS1 and LS2 steering racks. Coming in a set of three and including 1mm, 1.5mm and 2mm plates, they make adjusting the steering Ackermann a lot easier and faster. Drivers only need to undo the ball-studs on the steering plate enough to slide the shims in, then re-tighten. The plates are ultra-lightweight and durable, and allow 1mm to 4.5mm of Ackermann adjustment overall.

View another image here

July 13, 2017

RC Maker Tire Line Remover V2

New from RC Maker is the updated Tire Line Remover Tool. Based off the same concept as the original Tire Line Remover, the V2 is stronger, sharper and safer to use. The tool was designed to cut the centre moulding line off rubber tires, specifically for touring car and formula applications, allowing maximum tire performance from the first lap without grinding or sanding of the tire’s surface.

View another image here

July 4, 2017

RC Maker Awesomatix carbon tweak stick

New from RC Maker is the carbon fibre tweak stick for the Awesomatix A800 and A700 touring cars. Featuring a full carbon fibre construction, it is lightweight and disassembles for easy transportation. The tweak stick aids to pin the car down onto a flat surface with a single hand, whilst tightening the top deck screws with your other hand. Due to Awesomatix’ unique design not having shock towers, the tool utilises extension plates which exert even pressure onto the bulkheads left and right, front and rear. The design locates the extensions onto the bulkhead using locating lugs, which makes it quick, easy and accurate to use. Thick O-rings simply locate the extensions in place, which can be adjusted to suits the driver’s needs. Not requiring removal of anything to use, the strong carbon tube clears all spur gear sizes, as well as the antenna tube and belt tensioner. The tool fits both AM19-2 and AM19-4 upper bulkhead caps on the A800, and all top-deck configurations on the A700 without diff covers.

View more images here