Red RC » Revolution Design

September 11, 2025

Revolution Design 1:10 Ultra High-Downforce Wing

New from Revolution Design is this 1:10 offroad Ultra High-Downforce 7″ Wing. Aimed at racers looking for maximum control in low-grip conditions, it is specifically designed for dirt tracks with limited traction as well as wet or slippery astroturf, this wing provides outstanding downforce and stability. The extra tall side dams ensure superior side bite, while the included centre divider further improves straight-line stability and cornering precision. Thanks to the pre-cut design, installation is quick and hassle-free.

View wing mounted here

September 9, 2025

Revolution Design B84 Aluminium Bellcrank Set

Adding to its line-up of aftermarket up grade parts for the Team Associated B84, Revolution Design has released this Aluminium Bellcrank Set to improve the steering system on the 1:10 4WD Buggy. Machined from high-quality 7075 aluminium, it replaces the stock plastic parts, providing enhanced durability and precision. The rigid design minimises steering play, resulting in a more direct and accurate steering response.

View additional image here

July 15, 2025

Revolution Design Tungsten Battery Weights

New from Germany’s Revolution Design come these two Tungsten Battery Weights. The Shorty Battery Weight is a precision-ground 0.5mm tungsten plate that adds 42 grams of ballast directly beneath any 95 mm shorty LiPo pack. Because tungsten has a density of about 19.3 g/cm³—more than twice that of brass (≈ 8.5 g/cm³) and steel (≈ 7.8 g/cm³) – the plate can be less than half as thick as common 1–1.2 mm brass or steel alternatives. The lower profile lets the battery sit roughly 0.7 mm deeper in the tray, dropping the car’s centre of gravity for crisper turn-in and more stable landings on high-grip tracks. Machined edges and a matte finish give the plate a premium look, while the raw tungsten resists corrosion without additional coatings. Using the same 0.5 mm tungsten architecture as its shorty sibling, the full-length 2S stick pack Tungsten Battery Weight adds a concentrated 60 gram exactly where racers want it, under the LiPo and as low as mechanically possible.

Source: RDRP [revolution-rc.com]

May 28, 2025

Revolution Design XB4 7° Aluminium Caster Block Set

More new Xray option parts from Revolution Design Racing Products with the release of these 7° Aluminium Caster Block Set for the XB4 1:10 4WD Buggy. These a precision-machined upgrade parts are designed to increase strength, durability, and consistency on the track. Based on the proven RDRP design philosophy, these caster blocks are machined from aircraft-grade 7075-T6 aluminium to provide the perfect balance of reduced unsprung weight and maximum strength. The 7° caster angle, used by most Xray drivers, gives the car more initial steering. This makes the car more predictable and the overall steering response more stable. The black anodised finish with silver chamfered edges not only improves wear resistance but also gives the car a premium factory look.

View more images here

April 28, 2025

Revolution Design XB2’25 Ultra Battery Mount Set

Another new Xray XB2’25 buggy part upgrade from Revolution Design comes this Ultra Battery Mount. Designed as a direct replacement for the standard plastic battery holder, this set combines improved durability, smart functionality, and a clean, high-end look using premium materials and precision machining. Machined from high-quality 7075-T6 aluminium with a black anodised finish and silver chamfered edges, the mount delivers both strength and style. Lightweight carbon fibre battery tabs keep your shorty LiPo batteries firmly in place, preventing movement under acceleration or after landings. The set includes different washer heights and screw lengths, allowing you to easily adjust the mount to fit batteries of various sizes.

View more images here

April 16, 2025

Revolution Design XB2 Alu and Steel Bulkheads

New from Germany’s Revolution Design are these Aluminium and Steel Bulkheads for the Xray XB2’25 1:10 2WD Buggy. Weighing just 12-grams, the Aluminium 0° Bulkhead 0° is a premium upgrade part precision-machined from high-strength 7075-T6 aluminium and replaces the stock plastic bulkhead to enhance durability and handling performance. The black anodised finish with silver machined edges adds a refined racing look. The 45-gram Steel version is the ideal tuning part for drivers aiming to add front-end weight to their Team Xray XB2 2025. Made from high-quality steel, this bulkhead offers extreme durability and a significantly increased weight for improving balance and front traction on low-grip surfaces.

View more images here

September 22, 2021

RDRP T6.2 +4mm LCG aluminium chassis

Based on the popular Revolution Design Racing Products +3mm chassis for the RC10 B6.2, the new T6.2 +4mm LCG 7075 aluminium chassis as the name suggests adds 4mm of wheelbase. This is to improve handling in high-bite track conditions such as carpet and Astroturf, making the truck easier and faster to drive at the same time. One step ahead of the kit item, the new chassis is already prepared to accommodate new-generation servo mounts such as the B6.3 kit item or the RDRP LCG Servo Mount set. Machined from aircraft-grade 7075 aluminium for strength and optimised flex characteristics, the black anodised surface is the perfect basis for a stealthy looking high-performance model race car. As with the previous buggy version, the chassis comes with a low centre of gravity 7075-T6 motor plate that puts your motor as low as possible into the chassis cut out. Both the chassis and motor plate work exclusively with the laydown gearbox. In addition to the LCG motor position, cut outs in the chassis plate move the battery position for an even lower overall centre of gravity. With its silver edge details and laser-etched logos the chassis will not only ensure performance, but also attract attention in the pits. The chassis is also compatible with most bolt-on servo and electronics balance weight sets.

View another image of the chassis here

August 18, 2021

RDRP B6.3, T6.2 & SC6.2 slipper eliminator

RDRP’s slipper eliminator set helps you to shed some weight on your B6.3, T6.2 & SC6.2 where it counts most. The spur gear hub is made from black anodised aluminium with silver detailing to match the popular style of many aftermarket parts. As it is fully compatible with the kit top shaft and a variety of spur gears including RDRP’s lightweight ultra spur gear series and Team Associated’s, converting your 6.x series Team Associated vehicle to direct drive has never been so easy. For your convenience, the set includes spur gear mounting hardware, slipper bolt and nut.

View the mounted part here