Red RC » Team Associated

December 19, 2016

RDRP B6 brass gearbox brace

Available now from Revolution Design Racing Products is the brass gearbox brace for the Team Associated B6-series of buggies. The brace is a direct replacement for the kit’s lightweight composite part and it adds valuable weight to the rear end especially when running in low-traction conditions or when the track is getting bumpier. Machined from black-coated brass and sporting gold-colour chamfered edges the part weighs in at 23g which shifts the weight bias further back. The incorporated anti-roll bar mounts add precision due to the sturdy material, further upping the buggy’s performance.

View another image here

December 19, 2016

3DRC Awesomatix caster fingers & new fan mounts

3DRC from Germany have introduced the Awesomatix caster fingers for the A700 and A800 touring cars as well as two new fan mounts. Starting with the caster fingers, a simple bolt-on design the 3-D-printed pointers are attached to the wheel axles and when combined with Hudy’s 1/10th on-road setup system they allow for easy and precise caster adjustment on the car’s front and rear suspension. The caster fingers come in sets of four.

Continue reading here

December 9, 2016

Schelle B6 Extreme Battery Strap & Shock Standoff set

Schelle Racing Innovations have introduced the Extreme Battery Strap and an aluminium shock standoff set for the Team Associated B6-series buggy. Starting with the battery strap, the part was designed for laydown gearbox equipped buggies run on medium to low grip dirt as it allows to shift more weight towards the rear end of the vehicle for improved rear traction. The pack is held in place by 3-D-printed 7mm hex battery stops which are easy to install with a 7mm wheel wrench. Stainless steel screws are included, but racers can upgrade to aluminium or Ti to shave weight. The brace fits all five hole locations with a laydown transmission installed and the waterfall removed and it is also usable with the waterfall in place, that then allows for a total of three battery locations. The centre section with 3-hole option also allows to run a chassis brace tie rod.

Continue reading here

December 9, 2016

Team Associated 4WD 2.2″ 12mm hex front wheels

Coming from Team Associated are new 12mm hex 2.2 inch front wheel for 1/10th 4WD buggies. Offering the same dimensions as AE’s standard wheels but coming with the more poplar and durable 12mm hex the wheels will fit the new Team Associated B64D buggy without an adapter and they are also usable on the old B44 with the addition of a 12mm hex adapter. The wheels are available in sets of two in fluorescent yellow or white colour.

View more images here

December 7, 2016

3DRC B6 diff oil reminder plates

Coming from 3DRC are these handy diff oil reminder plates for the Team Associated B6 platform. Ideal for drivers that lost their latest setup sheet the plates help to indicate the currently used diff oil viscosity as they are simply attached to the rear camber mount brace using the existing screws. The set includes ten plates for 1,000 to 10,000 fluids and it is available through 3DRC’s Shapeways store.

Source: 3DRC [shapeways.com]

December 7, 2016

JConcepts B6 laydown gear shield

Coming through JConcepts’s Shapeways store is the laydown gear shield for the Team Associated B6. The part is a protection device that adds some protection to the spur gear while also shielding the body from unwanted scratches and rubs associated with normal driving use and wear and tear during a typical race outing. The 3D printed part slides directly on the Team Associated transmission case and aligns with the stock geometry. The motor plate installs just over the gear shield and is positioned as normal. The gear shield is protection for the spur gear itself but also protects the low-profile body designs such as the stock Team Associated body and JConcepts S2 body.

View more images here

December 6, 2016

JConcepts RC8B3e Strike 2 bodyshell

JConcept’s Strike 2 bodyshell is now also available for the Team Associated RC8B3e 1/8th E-buggy. The body samples elements from its famous relatives, the Finnisher and Silencer bodies, but packs a slightly refined image with the base enhancements to the design come from the added “finger” channelling on the front-pod, increasing mid-corner steering while a complete wicker section was added on the rear-pod to further plant the rear of the vehicle. The offset of the race-proven shell provides a compact fit for battery, motor and wiring assembly while on the battery side, the body has an added scoop which can be trimmed to release some hot air from the body. In addition, many pre-determined trim-lines have been added to allow extra flow behind the cab and also ream-able holes directly on the front of the side-pods to allow air straight into the body. The heavy channelling on the front windshield and upper cab keeps the Strike 2 aligned at high-speed while the side-pods have multiple hard-edge angles that spill off neatly into 90 degree side-panels. Just behind the cab, a large stabilizing fin and a sleek up-rising flows from the body like running water. The clear body set includes window templates and a decal sheet.

View more images here

December 6, 2016

3DRC B6 -2mm rear gearbox brace

Made for Team Associated’s B6 series of buggies is 3DRC’s new -2mm rear gearbox brace. The 3-D-printed part is of an updated design, based on a stock-part modification carried out by European high-class AE drivers, that lowers the standard camber link mount by 2mm, resulting in different roll centre settings that can be beneficial especially in high-grip carpet conditions. The brace comes including a set of shims that allows to easily revert to the standard setting and it is available through the brand’s Shapeways store.

View another image here