Red RC » Team Associated

December 7, 2016

JConcepts B6 laydown gear shield

Coming through JConcepts’s Shapeways store is the laydown gear shield for the Team Associated B6. The part is a protection device that adds some protection to the spur gear while also shielding the body from unwanted scratches and rubs associated with normal driving use and wear and tear during a typical race outing. The 3D printed part slides directly on the Team Associated transmission case and aligns with the stock geometry. The motor plate installs just over the gear shield and is positioned as normal. The gear shield is protection for the spur gear itself but also protects the low-profile body designs such as the stock Team Associated body and JConcepts S2 body.

View more images here

December 6, 2016

JConcepts RC8B3e Strike 2 bodyshell

JConcept’s Strike 2 bodyshell is now also available for the Team Associated RC8B3e 1/8th E-buggy. The body samples elements from its famous relatives, the Finnisher and Silencer bodies, but packs a slightly refined image with the base enhancements to the design come from the added “finger” channelling on the front-pod, increasing mid-corner steering while a complete wicker section was added on the rear-pod to further plant the rear of the vehicle. The offset of the race-proven shell provides a compact fit for battery, motor and wiring assembly while on the battery side, the body has an added scoop which can be trimmed to release some hot air from the body. In addition, many pre-determined trim-lines have been added to allow extra flow behind the cab and also ream-able holes directly on the front of the side-pods to allow air straight into the body. The heavy channelling on the front windshield and upper cab keeps the Strike 2 aligned at high-speed while the side-pods have multiple hard-edge angles that spill off neatly into 90 degree side-panels. Just behind the cab, a large stabilizing fin and a sleek up-rising flows from the body like running water. The clear body set includes window templates and a decal sheet.

View more images here

December 6, 2016

3DRC B6 -2mm rear gearbox brace

Made for Team Associated’s B6 series of buggies is 3DRC’s new -2mm rear gearbox brace. The 3-D-printed part is of an updated design, based on a stock-part modification carried out by European high-class AE drivers, that lowers the standard camber link mount by 2mm, resulting in different roll centre settings that can be beneficial especially in high-grip carpet conditions. The brace comes including a set of shims that allows to easily revert to the standard setting and it is available through the brand’s Shapeways store.

View another image here

December 6, 2016

T-Works RC8B3 aluminium axle shafts

twoT-Works RC8B3 aluminium axle shaftsrksrc8b3alloyaxles

Coming from T-Works and made for the Team Associated RC8B3 and RC8B3E are aluminium front and rear axle shafts. They are machined from high-quality aluminium and hard-anodised for wear. Multiple cross pin holes allow to switch to a new pair of holes once the currently used ones start to wear out. The axle shafts come in pairs and include suitable grub screws.

Source: T-Works [rc-tworks.com]

December 5, 2016

3DRC 40mm Fan Booster & B6 super light slipper nut set

3DRC have introduced two new products in the form of the 40mm Fan Booster for 1/10th off-road buggies and a super light slipper nut set for the Team Associated B5 and B6 series of vehicles. Starting with the Fan Booster, the 3-D-printed part accommodates most 40mm fan units and it makes for more efficient motor cooling thanks to channelling the cooling air towards the motor can. The fan mount is of a heatsink design for cooler looks and it works with many of today’s off-road buggies.

Continue reading here

December 5, 2016

Avid 12mm V2 Team Associated shock pistons

Made for Team Associated’s V2 1/10th scale shock absorbers are Avid’s 12mm V2 shock pistons. The machined and highly precise V2 pistons offer a conventional setup with square 90 degree edges and a tight fitting design for reduced blow-by, resulting in improved damping efficiency and accuracy. The pistons fit the screw-type V2 12mm shocks and they are available as 2×1.6mm, 2×1.7mm, 3×1.4mm and also a blank version in sets of two pieces.

Source: Avid [avidrc.com]

December 3, 2016

Team Associated SC28 Lucas Oil ready-to-run truck

Coming from Team Associated’s Qualifier Series of RTR vehicles is the SC28 Lucas Oil ready-to-run short course truck. Sporting Carl Renezeder distinctive livery the SC28 comes complete with everything needed in one box – ready to rip around the corners, fly over the jumps and speed across the finish line. The 175mm long 2WD micro truck weighs in at about 100g and it comes including an integrated speed controller/receiver unit, 2.4GHz radio system and the Carl Renezeder replica bodyshell.

View more images here

December 2, 2016

Exotek introduce new 2WD option parts

Coming from Exotek are a range of option parts for several popular 1/10th 2WD buggies such as the HB Racing D216, the TLR 22 3.0 and the Team Associated B6. Starting with the D216 part, the Flite motor plate is a fully CNC-machined affair made of high-quality 7075 aluminium. The vented design will keep the motor running cooler and longer for that extra edge. Aggressive cut outs allow the heat that builds up inside the gear cover to vent out thus lowering overall motor temperatures. The extra machining also reduces the weight down to 11.8g but the critical motor mounting areas are still intact to maintain solid motor mounting and gear mesh. Extra cut outs on the bottom side make sure that debris is ejected for free running gears. The part comes polished, anodised in black and laser-etched.

Continue reading here