Red RC » Vigor RC

March 14, 2017

Vigor RC BD8 carbon fibre flex chassis & bumper brace

Vigor RC have introduced two new carbon fibre option parts for the Yokomo BD8 in the form of a flex chassis and a front bumper brace. Starting with the chassis, the part is machined from high-quality 2.5mm material and special cut-outs make for increased flex which results in higher corner speeds. The chassis weighs in at 66g, about the same as the standard 2.25mm chassis. The second new part is a carbon fibre front bumper brace that was designed to replace the standard composite plastic item with a more rigid and also cooler looking item. The brace includes two carbon fibre bushings.

View more images here

November 20, 2016

Vigor RC introduce new TRF419X carbon fibre options

Vigor RC have introduced new carbon fibre option parts for the Tamiya TRF419X touring car. First up is a 2.25mm lower chassis that features a fully symmetrical design, offering equal steering characteristics in both directions. On top of this the chassis provides higher corner speeds and improved car balance. Next up are 2.0mm and 1.6mm carbon fibre upper decks. A direct replacement for the stock part the top decks allow to fine-tune the overall grip available with the thinner 1.6mm plate being recommended especially for low-grip conditions. Last but not least are carbon fibre battery retainers. The L-shaped parts keep the battery in place even in hard impacts and they come in sets of two.

View the other new parts here

November 10, 2016

Vigor RC BD8 carbon tweak rod

New from Vigor RC is this carbon tweak rod for the Yokomo BD8. Featuring a special cutout for BD8’s offset spur gear, the rod helps to easily and conveniently remove any chassis tweak even when using large diameter spur gears on the low profile chassis of the BD8.

Source: Vigor RC [vigorrc.com]

October 30, 2016

Vigor RC XB2 carbon fibre chassis & battery brace

Coming from Vigor RC and made for Xray’s XB2 ’16 and ’17 are a carbon fibre chassis and a battery brace. Starting with the chassis, the part is machined from high-quality 2.5mm carbon fibre and it is designed to replace the standard aluminium chassis. The lightweight material saves about 30 percent of weight with the carbon fibre chassis weighing in at about 86g. It fits the carpet and dirt edition kits, allows the use of several battery positions and it includes a protective chassis skin and mounting hardware.

Continue reading here

September 2, 2016

Vigor BD7 bulkhead spacers & steering wheel pads

Vigor have introduced new fine-tune bulkhead spacers for the Yokomo BD7-2016 car as well as high-grip steering wheel pads. Staring with the spacer set, already introduced in 1.0mm and 1.5mm specification the new 0.5mm and 0.8mm set allows for finer steps of bulkhead and motor mount raising. Using the spacers improves chassis flex and roll, meaning greater traction depending on the track conditions. As for the high-grip steering wheel pads, the rings are made of a special soft plastic that is available in eight colours and that is very easy to clean despite the bright colours.

View the steering wheel pads here

July 26, 2016

Vigor BD7-2016 lower bulkhead spacer set

Coming from Vigor and made for the Yokomo BD7-2016 touring car is a carbon fibre bulkhead spacer set. The plates allow to raise the front and rear bulkheads as well as the motor mount to give slightly improved flex which can be beneficial in certain track conditions. The set includes four 1.0mm and 1.5mm lower bulkhead spacers as well as two 1.0mm and four 1.5mm lower motor mount spacers, all made from high-quality carbon fibre.

View another image here

April 5, 2016

Vigor RC BD7 & T4 tweak plates

Vigor RC have released these two tweak plates for the Yokomo BD7 and Xray T4 touring cars. Made from 5mm thick high quality acrylic, they have been designed to have the same chassis plate outline as the car its for. Works as any normal tweak plate does, it comes with a carry case to protect it while being transported or stored.

View the T4 tweak plate here

March 14, 2016

Vigor RC BD7 44mm rear dual joint driveshafts

Vigor RC have introduced a set of 44mm rear dual joint driveshafts for the Yokomo BD7 touring car. Made from high-quality spring steel and featuring 1.8mm diameter cross pins the driveshafts are meant to offer a significantly higher durability while the included thin 3mm bearings make the driveshaft longer for smoother cornering at higher speeds. The rear shafts can also be used in the front of the car for fine-tuning purposes.

Source: Vigor RC [vigorrc.com]