Red RC » Xray

February 29, 2016

RSD X12’16 aluminium chassis conversion kit

RSD X12'16 aluminium chassis conversion kit

Available soon from Reflex Racing is the RSD aluminium chassis conversion kit for the Xray X12’16 1/12th scale pan car. Cut from 7075-T6 aluminium and coming black anodised and with machined silver edge details the chassis weights roughly 80 gram so the car will be around 20 gram heavier than in stock trim but the use of lightweight electronics, screws and accessories will help to bring the car near to minimum weight again to achieve maximum performance. Include in the chassis set, that was designed to bring the car’s centre of gravity as low as possible, is also a thin lower pod plate to match the chassis’ reduced thickness. The conversion kit will become available by mid-March.

Source: Reflex Racing [reflexracing.net]

February 25, 2016

Xray 50g stainless steel battery weight

Coming from Xray is a 50g stainless steel battery weight for the XB2 and other 2WD buggies. The plate allows to add weight to the lowest point of the chassis, making for an improved and more forgiving handling especially in high-grip and bumpy conditions. The plate comes laser-etched for easy identification, it is placed between the chassis and the battery pack and usable in all vehicles whose battery compartments allow the use side-by-side saddle packs.

Source: Xray [teamxray.com]

February 25, 2016

Spec-R T4’16 2.25mm carbon fibre chassis plate

Spec-R T4'16 2.25mm carbon fibre chassis plate

Coming from Spec-R and made for the Xray T4’16 touring car is a 2.25mm carbon fibre chassis plate. Cut from high-quality carbon fibre the chassis is of a fully symmetrical design with the milled motor pocket also apparent in the battery compartment to make for equal left-to-right flex characteristics. The chassis is a direct replacement for the stock part and available soon.

Source: Spec-R [spec-r.com]

February 24, 2016

Xray 1/10th buggy 10-piece wheel packs

Xray have introduced new 1/10th buggy wheel packs for 2WD and 4WD cars. Made for their line of XB2 and XB4 buggies the wheels are moulded from high-quality material to withstand impacts without damage while offering the right amount of flexibility at the same time. The wheels are available as 2WD front, 4WD front and general rear variant, they make use of 12mm wheel hexes and come in packs of 10 pieces. Beside Xray’s own 1/10th buggies the rims also fit many other cars that make use of the respective wheel off-set.

View the other wheel sets here

February 23, 2016

Xray XB4 graphite steering brace

Xray have introduced a carbon fibre steering brace for the XB4 buggy. Machined from 2.0mm high-quality carbon fibre the brace connects the two steering posts and it is meant to improve steering and jump landing on the expense of making the car less stable at the same time.

Source: Xray [teamxray.com]

February 22, 2016

Xray XB2 brass front bulkheads

Coming from Xray and made for the XB2 line of 1/10th 2WD buggies are two brass front bulkheads. Available as 26 degree and 23/29 degree variant the bulkheads not only help to adjust the front wishbones kick-up angle, they also add 46g of weight to the front most part of the chassis which can result in more on-power steering compared to running the standard composite blocks. Both bulkheads come laser-etched for easy identification with the 23/29 degree part requiring the use of the optional 23/29 degree aluminium front arm mount.

View the 23/29 degree bulkhead here

February 22, 2016

Xray NT1’16 – Coming soon

Xray NT1'16 – Coming soon

Xray have announced the soon release of the 2016 NT1 1/10th 200mm nitro on-road kit. The 2016 edition of the double World Championship winning car is expected to be an evolution rather than a revolution and we bring you more information on the vehicle as soon at they surface.

Source: Xray [teamxray.com]

February 19, 2016

Xray XB4 lightweight bodyshell

Coming from Xray and made for the XB4 4WD buggy is a lightweight bodyshell. Moulded from thin Lexan material the body is around 40 percent lighter than the standard kit body and it is recommended for the use on high-bite tracks as it will lower the buggy’s centre of gravity and make for more agile rotation into corners while at the same time a rear fin will help with stability on high-speed sections. The body comes clear and including window masks.

Source: Xray [teamxray.com]