July 27, 2013
Featuring the paint scheme of the truck raced by Eric Barron in the Lucas Oil Off Road Racing Series, the Toyota Racing SC10RS is a Ready-To-Run RC short course truck that features a water-resistant high-power XP brushless speed control, Reedy 3300kV brushless motor, and a water-resistant enclosed receiver box. Adjustable blue anodized aluminum V2 coil-over shocks and Short Course hex-drive wheels come standard with high traction racing compound rear tires for more grip. SC10 RS RTR Features: – 3-Time R.O.A.R. National Champion short course race truck – XP 2.4GHz radio system with XP metal gear steering servo – Water-Resistant High-Power…
July 25, 2013
A scale replica of the Johnny and C.J. Greaves Monster Energy/Toyota Racing truck raced in the Lucas Oil Off Road Racing Series and at the Crandon World Championship, this SC10RS Short Course truck features some major upgrades that include a water-resistant high-power XP brushless speed control, Reedy 3300kV brushless motor, and a water-resistant enclosed receiver box. The suspension also received an upgrade with the addition of adjustable blue anodized aluminum V2 coil-over shocks. The 2.6:1 ratio gearbox comes with a heavy-duty sealed gear differential and the externally adjustable V2 slipper clutch. Short course hex-drive wheels come standard on the SC10RS…
July 22, 2013
…fibre steering rack for Team Associated’s 2WD line of 1/10th off-road vehicles such as the B4, T4 and SC10. In the stock trim, the B4 steering swings a moulded plastic steering rack supported by bushings. The JConcepts alternative uses the flat panel 2.5mm material as the steering rack with the standard 2 locations for Ackermann adjustment. The new rack includes bearings for the system to glide on while small 1mm aluminium washers act as the crush sleeve between the bell-cranks and bearings. The rack is a direct replacement for all current and old-spec B4’s, T4’s and SC10’s. Source: JConcepts [jconcepts.net]…
July 3, 2013
New from Vision Racing comes this 3mm carbon fibre steering rack for Team Associated’s 1/10th 2WD off-road kits such as the B4, T4 and SC10. The rack offers four holes which gives finer adjustment of the steering Ackermann. Also the bushings included are machined for tighter tolerances, resulting in less slop in the steering system. Source: Vision Racing [vision-racing.net]…
June 26, 2013
The JConcepts anti-roll-bar kit for Team Associated SC10, T4 or B4 vehicles is the result of continuous driving on indoor, technical driving circuits which require the correct vehicle balance. JConcepts, together with test drivers Brian Kinwald and Paul Wynn, sought out the proper pivot placement on the front and rear a-arms which provided the best performance point, which became the basis for the new design. The inner mounted locations place more emphasis on wire diameter and less mechanical advantage which allows the driver a more finely tuned piece. The front inner placement position (SC10 and T4) is located by a…
May 30, 2013
…3rd to take the Team Associated SC10 equipped with JConcepts to the top of the podium. Brian Kinwald was awarded 2nd overall for his consistency while Chris Wheeler rounded out the podium in 3rd place. The 13.5 2wd class was amazingly tight during all 3 main events. Humpty Helms who looked strong in qualifying had an unfortunate problem in A1 forcing him out, allowing the young Justin Miller to the front of the pack to take A1. A2 started with Humpty up front again because of the Invert and Miller to the back of the pack. Humpty checked out from…
May 28, 2013
Vision Racing introduce two new carbon fibre option parts for Team Associated 1/10th off-road vehicles like the B4, T4 and SC10. First up is a short battery brace that does away with the somewhat longer original part. It is machined from 2.5mm quasi-isotropic material for balanced longitudinal and torsional stiffness. Also new is a speed controller shelf to allow the ESC to be mounted right before the shock tower. The shelf is cut from 2.0mm material and attaches right to the bulkhead using the existing screws. Source: Vision Racing [vision-racing.net]…
May 10, 2013
One of the best upgrades you can make to the Team Associated line of vehicles is a conversion to 12mm hex wheels. JConcepts has been on top of this conversion since its introduction with hex adapters and Mono wheels. A critical point of the conversion revolves around the front axle and surrounding geometry. Within the steering block the space is very tight and especially between the 2 front bearings where the front axles rests between the bearing bores in 1 plane and the king pin in the perpendicular plane. The JConcepts front axle design is based around high-grade titanium construction,…
