Red RC » P Off Road

February 24, 2017

Pro-Line ElectroShot VTR truck & new 1/5th tyres

Coming from Pro-Line are three new off-road tyres in the form of the ElectroShot VTR 4.0″ 1/8th truck as well as the Blockade and LockDown 1/5th truck tyres. Starting with the ElectroShot VTR 4.0″, the tyre comes from the mind of Ty Tessmann and is designed to perform just like a Hole Shot 2.0 while lasting significantly longer. The ElectroShot is a combination of Pro-Line’s Electron and HoleShot tread designs with connected bars in the centre where the heaviest tyre wear occurs and Holeshot pins everywhere else for maximum traction. The tyre will become available in M3 soft and X3 soft compounds.

Continue reading here

February 23, 2017

SWorkz S35-series front arm mount balance weights

Coming from SWorkz and made for the S35 series of off-road vehicles are brass front-rear arm mounts. Machined from high-quality material and sporting a shiny finish the parts help to add weight to the front end for improved steering response and optimised jump landing. The FR mounts are available as lighter 25g or heavier 35g variant.

View another image here

February 23, 2017

ProTek RC Euro LS-5 .21 5-port off-road engine

Available now is ProTek RC’s new Euro LS-5 3.5cc 5-port competition nitro off-road engine. Developed by top AMain and Novarossi pro drivers the engine will provide optimal power, run time and ease of tune. The power plant comes with a composite carburettor that resists heat and holds a consistent idle while the crankshaft and 5-port sleeve have been paired to provide linear power that produces a level of drivability that shreds lap times—throttle response is consistent throughout the entire RPM range. The setup of the long stroke engine allows for nine and a half to ten minutes of run time and to comes including a C6TGC turbo-style glow plug.

View the features, specifications and another image here

February 23, 2017

Serpent Cobra SRX8e – Coming soon

Serpent have released a first teaser image of their forthcoming Cobra SRX8e 1/8th E-buggy kit. The Billy-Easton-designed buggy is based off of its nitro sibling and will make a first public appearance at this week’s The Dirt Nitro Challenge. The kit is set for a release in April and we bring you more information as soon as they surface.

Source: Serpent [serpent.com]

February 23, 2017

Factory RC ROAR motor tech plate

Coming from Factory RC is the ROAR motor tech plate. This go/no go tech plate allows for quick inspection of any ROAR-approved motor for physical dimension requirements. The plate is machined from 2.25mm carbon look plate to the maximum tolerances allowed by ROAR. This allows the individual inspecting motors for legality to use a non magnetic tool to inspect the rotor and can for dimensions to assure legal racing. The rotor can be inspected using the length and diameter slot which also inspects for the 7.00mm internal OD shaft. There is also a pass through hole for the rotor body as well. Notches help to inspect the can diameter and length, as well as the 14.5mm “plug” go/no go gauge for the can/stack. This leaves only the stack length for inspection with a pair of digital callipers to finalise inspection which is easy to do since the stack is not magnetic. All measurements are clearly marked and the plate has so far been successfully used at various races.

Source: Factory RC [factory-rc.com]

February 23, 2017

Factory RC YZ-4 CF shock towers & shorty battery brace

Coming from Factory RC and made for Yokomo’s YZ-4 4WD buggy are new carbon fibre shock towers and a shorty battery brace. Starting with the shock towers, available soon is a “flat” front tower as well as a rear item that offers additional shock mounting holes while also allowing to adjust the rear wing height. Both are cut from high-quality 4mm carbon fibre. Also new is a shorty LiPo brace for sideways mounted batteries and designed for the use with Factory RC’s delrin battery stoppers. All parts are available soon.

View the other new parts here

February 23, 2017

JQRacing THECar Black Edition 1/8th nitro buggy kit

JQRacing have released first images and information on the forthcoming Black Edition THECar 1/8th nitro buggy kit. Optimised in all aspects, the 2017 variant will feature a new longer wheelbase 3mm Ergal chassis as well as a range of new suspension parts such as crash resistant hinge pins, an updated caster angle, an updated king pin angle, new carbon fibre steering plates, a new 2.0 Ackermann plate with steel bushings, and it the kit will include special laser-etched alloy parts and a new bodyshell. The buggy is available for pre-order soon with the official release date being set for the April 1st.

View the JQ-optimised features list and more images here

February 23, 2017

175RC.com shorty LiPo brass weights

175RC.com have introduced a range of under LiPo weights for shorty battery packs. Made from heavy brass material and coming in four different designs the weights allow not only to up the overall weight of the vehicle but also to simply adjust the weight distribution. Type A is a plain weight available as 18g or 36g variant while Type B, available as 12g and 23g versions, is very versatile. It can be run in 2WD buggies and flipping the plate forth and back allows to adjust the front to rear weight bias while in 4WD buggies it can be used to bring more weight to the inside or outside. The Type C weight, with outer cut outs, makes for a more centralised weight balance while Type D put more weight to the outer sections. The latter two are available as 12g or 23g versions.

View the Type B, C and D weight here