Red RC » Exotek

November 20, 2013

Exotek DEX210 aluminium suspension mounts

Exotek Racing introduce new low roll centre aluminium suspension mounts for the Team Durango DEX210 buggy. Available are a RF Hanger with shims, and two LRC mounts with standard or +0.5° toe-in setting. Starting with the RF mount, the part allows to use a 2mm lower roll centre with 0° or 1.5° kick-up or the standard roll centre with 0° or 1.5° kick-up by adding the included shims under the hanger. The easy shimming option does away with the need to disassemble the whole rear end of the vehicle only to change the roll centre or kick-up settings. The set is machined from 7075 aluminium, comes anodised and works with the DEX210 alloy chassis, DIMEC type A or the optional Exotek chassis both in MM and RM configuration.

Click here to continue reading

November 4, 2013

Exotek M10 spoked 24mm wheels

Exotek introduce the M10 spoked 1/10th rims for 24mm touring car tyres. Made from a special nylon formulation the fibre-free rims offer ideal flex characteristics for both asphalt and carpet racing. They are of a 0 off-set design, are black of colour, work with virtually any 24mm rubber tyre and come in sets of four.

Click here to view another photo

October 18, 2013

Exotek RB6 titanium front axles

New from Exotek come these titanium front axles for the Kyosho RB6 2WD buggy. At 5.5g per pair their are almost 50 percent lighter than the stock steel shafts while offering nearly the same rigidity. They are a direct replacement and designed to work with the stock spacer set.

Source: Exotek [exotekracing.com]

October 3, 2013

Exotek XB4 aluminium option parts

New from Exotek Racing come several aluminium option parts for the Xray XB4 buggy in the form of rear hubs, servo and wing mounts. Starting with the rear hubs, the parts are machined from 7075 aluminium and sport vertical camber ball stud mounting positions for easy roll centre adjustments using different thickness shims. Included with the parts that come in orange or black colour are 2mm spacers to match the stock geometry of the kit’s plastic hubs. Next up are aluminium servo mounts, again machined from 7075 aluminium. The parts offer higher rigidity and sport a lightweight design and come in orange or black colour. Last but not least are the aluminium wing mounts. They are of a heavy duty design and add a huge amount of durability while being light of weight at the same time. Just like the other XB4 parts they are available in orange or glossy black colour.

Click here to view the other new parts

September 24, 2013

Exotek 1/10th AE alloy & carbon option parts

Exotek have new option parts for 1/10th Team Associated off-road vehicles available in the form of rear ver2. hub carriers, a battery strap and an ESC tray. Starting with the hub carriers, they are designed for the use with B4, B44 and SC10 vehicles and are of an updated design that results in a 20 percent lighter weight. Vertically mounted ball studs make for easy roll centre adjustment using shims, allowing you to mimic the popular “C” or “A” setting of the original AE hubs. They use the same heavy duty oversized outer bearings, crush sleeve and shims as the factory team hubs and come as 0° toe item.

Click here to continue reading

September 13, 2013

Exotek F1 & Pan Car heatsink

Exotek introduce this heatsink for the use with pan and F1 cars. The special design allows the air to flow through the large fin section while the back of the heatsink gives enough clearance for high axle F1 or low axle 1/12th cars. The low-profile design also gives adequate body clearance and vented openings allow ‘open can’ motors to breath. The heatsink is machined from 6061 aluminium, comes in blue or black colour and simply clips onto the motor with no fasteners needed.

Click here to view more photos

September 4, 2013

Exotek RB6 alloy C-hubs & mid motor rear bulkhead

Exotek have new aluminium option parts for the Kyosho RB6 buggy available in the form of C-hubs and a mid motor rear bulkhead. Starting with the castor hubs, the parts are CNC-machined from 7075 aluminium and come anodised in Kyosho factory red colour. They weight in at 7g per set and are much stronger than the stock plastic hubs. The second new part is the mid motor rear bulkhead, again machined from 7075 aluminium. Coming red or black anodised the part is machined to weight just 12g while offering exceptional durability at the same time. The bulkhead works both with the stock plastic and Exotek’s optional carbon fibre shock tower.

Click here to view more photos

August 27, 2013

Exotek TEK-SCT v2 chassis conversion kit

Exotek Racing introduce the TEK-SCT v2 chassis conversion kit for the Losi Micro SCT, Micro Rally and Micro Truggy. The set contains a carbon fibre upper and lower deck as well as a battery brace made from the same special micro weave fibre material. Included is also a sliding motor mount, alloy bolt-in servo mounts and, especially for the v2, new alloy battery cups, an alloy steering guide and an alloy receiver mounting plate. The aluminium parts come blue anodised and included is also suitable hardware set.

Click here to view the features and more photos