Red RC » Brand

May 28, 2011

Xray Column – Racing Season ‘11 Full Running

The 52nd installment in the Xray column from Xray owner and chief designer Juraj Hudy is now online. In this months column, Juraj talks about this year’s races so far with a focus on their 1/8th scale World Championship debut with the new RX8 chassis.

Considering that some of the drivers only got their cars a few days before leaving for the Worlds, it was no surprise to see some of them building or finishing the car at the track. We handed out some of the last-minute new option parts for set-up tuning to all the team member, and then got to work.

Read the full column here.

Source: Xray [teamxray.com]

May 28, 2011

Pro-Line’s new ‘Dirt’ track

[youtube]http://www.youtube.com/watch?v=CdNgn-YzUyY[/youtube]

Pro-Line Racing have published a video showing their new 1/8th offroad and Short Course track at their premises in Beaumont, California. Designed and built by superstar track builder Joey ‘The Dirt’ Christensen, it incorporates two layouts, a smaller infield section for Short Course, while the 1/8th scale cars take in the outside perimeter which is bigger and features larger jumps. Aside from Pro-Line using it to help develop their future products, we can also expect some races to be held on this track in the near future so we will let you know when that happens.

May 27, 2011

Xray sign Ales Bayer

Xray have announced the signing of top Czech driver and multiple junior national champion Ales Bayer to their team. The former Losi driver, and brother of European finalist Martin Bayer, Ales will run his XB808 buggy and XT8 truggy at all upcoming National and International events.

Source: Xray [teamxray.com]

May 27, 2011

Xray RX8 2.6mm & 3.0mm rear anti-roll bars

Xray have released two new additions to their range of RX8 steel rear anti-roll bar wires. Allowing for additional tuning beyond the stock rear anti-roll bar, the new wires are available in 2.6mm and 3.0mm thickness, adding to the already available 2.8mm version. Manually measured, selected and straightened to eliminate all tweak, they are laser engraved for easy identification.

Source: Xray [teamxray.com]

May 27, 2011

Vampire Racing Type AB+ brushless motors

First shown at the Nuremberg toy fair early this year, the Vampire Racing Type AB+ brushless motors are now finally available. Not only a smart looking motor, but also with technical features like a heavy-duty front bearing or a side-feed sensor plug, this motor is an quality piece of engineering. Available from 4.5T to 8.5T, they are very reasonably priced to boot.

View the motor rear plate here

May 27, 2011

KO Propo Frequency Hopping-Spread Spectrum

With the knowledge gained from their DS-SS (Direct Sequence-Spread Spectrum), KO Propo have introduced their new FH-SS (Frequency Hopping-Spread Spectrum). This new spectrum allows for a stronger performance against interference and creates a better response time. Each module will have a different hopping pattern which avoids interference and allow you to operate the system alongside 50 other units. The operating distance has also been improved to 160m, which is twice the previous distance and finally the binding time has been reduced to 0.01 seconds or less, simply turn it on and drive. KO have released a pair of new FH-SS transmitter modules and new KR411FH receivers for the EX-10 Eurus, the RF904FH module, and the EX-1 UR / Mars Series & Esprit 3, the RF903FH module.

View the RF903FH module set here

May 27, 2011

Sweep Racing Cloud9 closed cell Insert

After extensive testing with molded grooved foam inserts, Sweep Racing have focused their efforts on the development of new closed cell foam inserts. Closed cell foam inserts have many performance benefits over conventional designs, such as increased durability, waterproof, reduced tire deformation during cornering and lighter in weight. These characteristics make their Cloud 9 buggy insert a major improvement over their previous designs. Sweep drivers have reported increased cornering capability and improved acceleration. The Cloud 9 inserts are scheduled to arrive at dealers very soon.

Source: Sweep Racing [sweepracing.com]

May 26, 2011

Xray XB808 lower suspension holders

Xray have released this set aluminium front and rear lower suspension holders for the XB808. CNC-machined from premium Swiss 7075 T6 aluminium and hard coated for extra durability and long life. The ultra-strong construction provides very long life and durability in even the most extreme racing conditions. The set includes all parts necessary for a complete suspension holder system upgrade. These new lower suspension holders provide an even greater range of adjustment for the front and rear suspension. Using different combinations of eccentric bushings, fine adjustment of front kick up, rear anti-squat, front toe-out, rear toe-in, front & rear roll center and front & rear track-width can be obtained. New reinforced bushings (included) have 1° and 0.5° eccentricity which allows up to 17 different positions. Super-fine adjustments can be made by increments of 0.5°. Includes heavy-duty suspension pivot pins that have been heat treated for increased strength.

View the rear suspension holders here