Red RC » RC Maker

January 16, 2020

RC Maker BD10 GeoCarbon bumper plate & battery brace

RC Maker have introduced new GeoCarbon carbon fibre optionals for the Yokomo BD10 touring car. First up is a bumper plate with stopper that sports a stylish, stealth and innovative design. This support contacts the bulkheads and prevents impacts from snapping the main chassis and are very important. The design includes a 5mm brace which sits below the plate, raising it to the correct height and significantly increasing the strength of the whole assembly. Upon resting, there is a 0.2mm gap between the bulkheads and the support, to prevent any rubbing and tweaking. This support will only be active in a crash. This provides the optimal solution to keeping the chassis on the brand new BD10 safe, whilst looking great at the same time.

Continue reading here

December 30, 2019

RC Maker T4’20 floating electronics weight plate

RC Maker have introduced their new floating electronics weight plate for the Xray T4 2020 touring car. The plate puts weight where it is needed most, to get the car up to he minimum weight and balanced. The set includes a carbon shim which floats it 0.5mm off the chassis from near to the centre of the car, meaning the plate itself has minimal to no impact on the flex of the chassis. On top of the plate, there is a 10g of brass weight to secure it in place. The plate attaches to the often unused antenna mount hole. If drivers still want to use this antenna mount, they can use an extra long screw through the lower weight, and thread the antenna mount on-top. The plate itself is 1mm thick and weighs in at 12g. The set coming in at 22g is a brilliant way to meet the limit, balance the car and have no impact on the flex characteristics of the chassis at the same time. Another added bonus, is owners can change chassis or clean the car, and simply remove the receiver, transponder and fan simply by undoing one screw. If drivers are after more weight for the car, RC Maker have a 1.5mm option plate available weighing in at 20g which can either replace the 1mm plate to bring the overall weight up to 30g, or added to the 1mm plate to make a total of 2.5mm, bringing it all the way up to 42g. The set comes packaged in a high quality black magnetic lid box with RC Maker logo on a clear front window, ensuring the plate is kept in perfect condition in transit.

View more images here

December 18, 2019

RC Maker T4’20 CentraFlex top decks

RC Maker have introduced their new CentraFlex top deck for the Xray T4 2020 mid-motor touring car. Based off RC Maker’s Awesomatix MMCX top deck, it builds on the brand’s foundations of believing in centrally located flex on touring cars. Several of the latest mid motor cars have entirely split front top decks. The reason for this is so that they can wrap around the front belt and still be symmetrical. However testing has shown that this “split” design can cause an imbalance in flex characteristics which was never before been an issue on rear motor cars, however on today’s Mid Motor cars can cause the car to be inconsistent and nervous, whilst having reduced on power and high speed steering. The CentraFlex is joined in-front of the spur gear, providing a much more centralised flex point. RC Maker have proven the “single side” design over the spur gear to be a consistent, tweak free solution and in testing found both physically and handling wise, the car was very balanced on left and right corners. As well as handling benefits, the design brings several fitment benefits such as increased clearance between the front face of the motor and the top deck for when the car is under high flex load as well as increased clearance between the edge of the motor and the top deck to fit all brands of motors, and all classes and sizes of pinion/spur combinations without any grinding of top deck or motor. Also installation and removal is much easier while providing a more durable design around the motor. The CentraFlex top deck is available in 2mm and 1.6mm thicknesses.

View more images here

December 6, 2019

RC Maker 3D Pro ESC wire organiser

RC Maker have introduced their new ESC wire organiser for the use with most brushless electronic speed controllers. Wiring is difficult, especially on the new mid motor chassis with the ESC behind the motor. The belt is in the way and there really isn’t much room. That is why the designers have gone and made it a whole lot easier for the drivers. 3-D-printed from high quality composite material, the wire organiser keeps all three motor wires, plus the sensor wire bunched together, and stuck down. The part is also very useful for keeping the wires organised in 1/12th on-road, and 1/10th off-road chassis and it accepts any wires, 12 gauge or smaller, and all sensor wires, flat or bunched. The organisers is usable floating or taped down using optional double sided tape.

View more images here

December 4, 2019

RC Maker T4’20 GeoCarbon bumper plate with stopper

RC Maker have introduced their new GeoCarbon front bumper plate with stopper for the Xray T4’20 touring car. The plate and stopper feature a stylish, stealthly and innovative design and the parts add extra protection to the front of the car as the support contacts the bulkheads and prevents impacts from snapping the main chassis and are very important. The design integrates the stopper under the main bumper plate, lining up with the bearing mounts on the front bulkheads. In the event of a crash, the force will be transferred through this and keep the chassis in tact, with minimal effect on the bulkheads. The brace recesses over the small bumper posts enabling it to get low enough to align with the bulkhead. When tightening the upper plate, it clamps the whole assembly down tightly. Upon resting, there is a 0.2mm gap between the bulkheads and this support, to prevent any rubbing and tweaking. The bumper plate also features three sets of holes, allowing drivers to adjust the bodyshell forwards and backwards as seen on the standard plates. The integrated stopper does not move, it will be in the same place regardless of the body post position. Due to the design, the plate can also stay in place when removing the front anti-roll bar.

View more images here

November 25, 2019

RC Maker brass floating battery mounts & battery weight

Coming from RC Maker are new brass optional parts such as floating battery mounts for the Awesomatix A800, Yokomo BD9 and Xray T4 as well as a 33g LCG battery weight plate. Starting with the floating battery mounts, reducing external factors on chassis flex has always been RC Maker’s mission. Chassis flex is one of the most important and sensitive tuning options today, and thats why the company strongly believes it must take all measures to reduce the impact that the electronics may have on chassis flex. The battery is roughly 300g, with a fully flat base contacting the chassis. This, even though it may be loose on the car, will have a detrimental impact on chassis flex. RC Maker’s new brass battery holders float the battery off the deck, and drastically reduce the impact the battery has on the flex of the chassis. The Awesomatix specific mount attaches to all of the Awesomatix model battery mounts, both factory and aftermarket. The Awesomatix mount is also usable on the Xray T4 2017 to 2020 models using optional, non-plastic battery mounts. The Yokomo variant installs directly to both standard plastic, and optional aluminium Yokomo brand battery mounts.

Continue reading here

November 14, 2019

RC Maker GeoCarbon TC wing support set

RC Maker have introduced their new GeoCarbon wing mounting solution for touring cars. Developed for serious racers, it is designed to protect the wing, and wing strut in crashes, as well as provide maximum downforce and efficiency from the wing. The “L” shaped design can be switched to left and right to fit different bodies and wing positions, and offers rearward and outer wing chord support. Flexing of the wing in high speed straights and corners can lead to unpredictable handling. This is due to the wing folding back, but also, when the wing folds back the sides of the wing lift up to even further increase the detrimental impact. Our side facing supports minimise this lifting, which also in turn minimises flexing of the wing backwards. This creates an overall more stable wing in every direction! Also included is an adjustable carbon fibre support for under the bodyshell. This clamps the wing and body between two pieces of carbon, providing more support and stiffness. It can be shifted forward or backwards to suit different bodies and wing positions. The set is complete with two lightweight alloy screws and two lightweight alloy nuts to provide a lightweight, stable solution to mounting the wing.

View more images here

November 6, 2019

RC Maker Montecarlo anti-tuck wing mounts

Coming from RC Maker and made for Mon-Tech Racing’s Montecarlo touring car body shell is the anti-tuck wing mounting set. 3-D-printed for a low weight and exceptional durability the mounts prevent body tucks behind the rear wheel arch during racing, as well as inconsistencies on high speed tracks and in windy conditions, causing the bodyshell to vibrate. The new V2 Lite set weighs in at only 5g for the pair, and it only requires one additional M3 screw other than the wing mounting screw to secure the strut behind the wheel arch. Using existing upper wing buttons, owners can screw directly into the strut securing it at the top whilst also securing the body’s wing, making for quick and easy body preparation.

Source: RC Maker [rcmaker.com.au]