Red RC » Team Associated

May 28, 2013

Vision Racing Associated buggy & truck options

Vision Racing introduce two new carbon fibre option parts for Team Associated 1/10th off-road vehicles like the B4, T4 and SC10. First up is a short battery brace that does away with the somewhat longer original part. It is machined from 2.5mm quasi-isotropic material for balanced longitudinal and torsional stiffness. Also new is a speed controller shelf to allow the ESC to be mounted right before the shock tower. The shelf is cut from 2.0mm material and attaches right to the bulkhead using the existing screws.

Click here to view the other new part

May 26, 2013

PSM B4.2 carbon front shock tower

PSM have produced this new carbon front shock tower for the Associated B4.2, which comes as a complete set with all required mounting hardware. Made from glossy 5mm carbon fibre, it is super lightweight at only 14.0g and gives your B4 a nice factory team look. It also features an additional inner shock position which will be a big advantage on high bite tracks such as carpet or astroturf.

View the mounted shock tower here

May 18, 2013

P-S-R OT1 low-friction bearing sets

Power-Save-Racing introduce their OT1 low-friction ball bearing sets for many of today’s 1/8th off-road buggies. Available for the 8ight 2.0/3.0, RC8, MBX6/7, MP9 TKI2/3, RB One R and XB9 the sets include RS and ZZ shielded bearings with the RS ball races are used in very exposed areas whereas the low friction ZZ shielded bearings are used in protected parts of the chassis. The result is a drivetrain with less friction compared to a car running all-rubber sealed bearings.

Source: Power-Save-Racing [power-save-racing.de]

May 16, 2013

JConcepts B44.2 aluminum bulkhead cap

New from JConcepts comes this replacement bulkhead center cap for the famous B44.2 buggy kit. The machined aluminum component, anodized in blue, is a handy replacement for the stock plastic unit and is a drop-on to the center slipper assembly. With the motor mount and bulkhead as one assembly in the B44 vehicle, temperatures peak out and transfer through the entire center assembly allowing the new cap to act with heat-sink capability. The stout design with external ribbing has increased strength over the plastic unit, is symmetrical in design and adds a higher level of detail and aesthetic appeal to an already championship vehicle.

Click here to view the mounted part

May 10, 2013

JConcepts Associated front axles for 12mm hex

One of the best upgrades you can make to the Team Associated line of vehicles is a conversion to 12mm hex wheels. JConcepts has been on top of this conversion since its introduction with hex adapters and Mono wheels. A critical point of the conversion revolves around the front axle and surrounding geometry. Within the steering block the space is very tight and especially between the 2 front bearings where the front axles rests between the bearing bores in 1 plane and the king pin in the perpendicular plane. The JConcepts front axle design is based around high-grade titanium construction, an outer bearing crush step and an inner 4-40 locknut for security. The design eliminates c-clips, screws and other items which are hard to detect of issues which limit performance. Available or the B4.2, T4.2 and SC10, this free spinning design includes axles, 4-40 mini lock-nuts, thin axle shims, decal and assembly instructions.

View the other axle sets here

May 9, 2013

Associated updated XP Digital servos

Team Associated have released an updated range of XP Digital water-resistant servos. The perfect replacement or upgrade for your RTR vehicle they feature water-resistant o-ring sealed cases, high-impact case material and precision metal gears provide maximum durability, while high-torque motors provide maximum performance in both steering and throttle/brake applications. Available in 5 new versions for different applications.

Source: Associated [teamassociated.com]

May 3, 2013

Associated 12mm big bore shock pistons

Associated have released more new 12mm big bore shock pistons to increase the tuning options of your big bore shocks. Flat, machined pistons of two 1.6mm holes, three 1.4mm holes, and four 1.3mm holes are available in packs of four. The Big Bore shocks fit the B4.2, B44.2, T4.2, SC10, SC10B, and SC10GT, including RTR and FT versions.

Source: Associated [teamassociated.com]

April 26, 2013

DE Racing Borrego wheels for ZX5 & SC8

DE Racing have announced some updates to their Borrego wheel line with the release of this front wheel for the Kyosho ZX5. Also new is a Borrego 17mm SC wheel for the Team Associated SC8 and other SC conversions using a 17mm hex. Both new wheels are available in white, yellow, silver and black.

View the SC8 wheels here