New from Serpent and made for the 977 Evo 1/8th scale kit is a radio plate support post. The 7075-T6 aluminium part will stiffen the front end of the car which can be a helpful tuning aid on very high-bite surfaces. The part is a direct fit on the Evo and must be used in combination with the central flex system to make it work.
Source: Serpent [serpent.com]
German company PSM have introduced a range of option parts for the Team Associated RC8B3 buggy. First up is a set of aluminium shock standoffs. Made from high-quality 7075-T6 aluminium and coming with EV2 silver coating for improved surface protection the set weighs in at only 11g including mounting material. The 12-piece set is made in Germany and includes the standoffs, shock alignment shims as well as counter shims. Also new are 5mm front and 4mm rear carbon fibre shock towers. Made from authentic PSM semi-gloss finish material the ultra lightweight parts are direct replacements for the stock shock towers and they weigh in at 16g and 18g respectively.
Click here to view more photos
LRP’s VTEC Groove 2WD front and rear tyres are now also available with white multi-spoke rims. The proven tread design allows to use the tyres on a range of surfaces while the special J-compound rubber makes for optimised traction and a high durability. Coming pre-glued and including moulded foam inserts the wheels are usable for many of today’s 1/10th 2WD off-road buggies with 12mm wheel hex adapters.
Source: LRP [lrp.cc]
Round four of the German West division 1/8th E-Buggy regionals was held at the RCRT Duisburg track. Hot weather made for dry and dusty conditions and this caused some headache for the drivers and after the qualifiers it was Chris Kammann who came out fastest from Lukas Strothmann an Max Kempchen. In the single 10-minute A-main leg Chris was able to conserve his performance to take a commanding win some 14 seconds in front of second placed Lukas Strothmann. Peter Schulte-Batenbrock would round out the podium in 3rd.
Source: Team Durango [team-durango.com]
Coming for Exotek’s recently introduced Exo22 chassis conversion kits are two replacement bottom plates. Made from either dark anodised 3mm 7075 aluminium or 2.5mm carbon fibre the plates not only are a direct replacement but they also act as a tuning aid as both are interchangeable and offer different characteristics. Using the carbon plate in a former aluminium car makes the buggy lighter and more responsive while the alloy chassis maximises stability and traction beside offering a lower centre of gravity.
Click here to view the carbon fibre chassis
The OS/Futaba Nitro Challenge was held at the St. Louis Dirtburners track with a turnout of over 200 entries. The Levi Jackson built track was a lot of fun, watered and the grip level was pretty decent. As the sun got strong though the track began to dry quicker and it was made a decision to let it groove in early and hopes were it would hold together. By the end of practice on Friday everyone became aware that this wasn’t going as planned. The track got super dry and while there was a nice groove it had little holes in that groove that continually grew and spit out sand, dirt, and rocks. By the end of the weekend the track was a complete challenge as finding a setup to traverse the conditions was tricky. Everyone bemoaned about finding consistency and some found themselves using medium hardness tires, even though the conditions were loose.
Click here to continue reading
Upgrade RC’s Vortex 10 Seven Lexan wing was designed to suit mid-motor 2WD and 4WD 1/10th buggies. Just like its predecessor the unique Dimple System helps to decrease friction drag at higher speeds and increases downforce with reduced drag at low speeds. The wing comes with a set of two side number plates and mounting grids for easy installation.
Source: Upgrade RC [rcidcustom.com]
The HPI Racing Pro-Series Temp Driver is a combined infra-red temperature gauge and a flat blade screw driver to adjust the needles of nitro engine carburettors. No longer multiple tools are needed trackside or while bashing to obtain perfect engine tuning. The tool allows to check the temperature of any nitro engine properly as the plug obtains the correct temperature reading, while the flat blade driver helps to fine-tune all carburettor needles. The tool is supplied in a metal tin and it can also be used by electric drivers wanting to keep an eye on motor, speedo, battery or tyre temperatures.
Click here to view the specifications and more photos
