Red RC » RC Maker

February 3, 2020

RC Maker GeoCarbon V2 A800 MMX series steering arms

Coming from RC Maker and made for the Awesomatix A800 MMX and MMXA are new GeoCarbon V2 front and rear steering arms. Starting with the front arms, the V2 variants provide more flex than the standard AM14LS arms, providing more traction on asphalt, ETS carpet and CRC Black carpet. They are 3mm thick, and are designed with only the outer AM14LS hole for the new SB1 single bellcrank steering on the latest evolution of Awesomatix MMX/MMXA chassis. As for the rear arms, these provide more flex than the standard AM23-1 arms, again providing more traction on asphalt, ETS carpet and CRC Black carpet. They arms from as separate sets for the front and rear and they required the owner to either use long screws with AT21ST-A, or ST24M/ST24L with a nut for installation, as the holes have no thread.

View more images here

January 31, 2020

RC Maker A800 series front centre weight

RC Maker have introduced their latest brass option part for the Awesomatix A800 mid motor range in the form of a front centre weight. With the ultimate place to add weight to basically any car being the centre of the chassis, this weight locates in the dead centre in-front of the motor mount, extending to under the steering rack. Designed to be used with all the Awesomatix A800 mid motor variations, including the MMX, MMXA and MMCX, it is the perfect way of adding 10g in the centre and nice and low on the chassis. The weight also includes a 0.5mm carbon shim for spacing the weight off the chassis to minimise any flex impedance.

View the installed weight here

January 30, 2020

RC Maker A800MMX SlimFlex top deck set

RC Maker have introduced their new SlimFlex top deck set for the A800MMX and MMXA. The MMX/MMXA top deck features two separate short top decks, drastically reducing the leverage on the carbon. This means the top decks need to be narrower and thinner than normal to achieve similar flex. Also the flex of the top decks front and rear is entirely symmetrical, so in order to achieve the optimum flex point, the car needs different flex settings front and rear to achieve optimum balance, which is to shift the flex point forward of centre. RC Maker’s SlimFlex top deck has this built in. The designers have optimised the profile of the top deck such that with the same ST019 flex setting, the flex point is shifted forward to provide the forward bias flex point that was achieved in their MMCX top deck.

Continue reading the report here

January 26, 2020

RC Maker CentraFlex BD10 top deck & post set

RC Maker have introduced their new CentraFlex top deck and post set for the Yokomo BD10 mid motor touring car. Conventionally in mid motor setups as seen on the BD10, the front of the top deck is entirely split in order to be able to slide the top deck over the front belt. This provides a significant amount of flex to the front of the car only, creating quite an imbalance in the top deck’s flex characteristics. The CentraFlex has been developed to slide in from the side under the belts, and due to the single sided design, can be joined in front of the spur gear to prevent excessive front top deck and bulkhead flex, bringing back the balance of front to rear flex provided by the top deck. As well as this, RC Maker have also added an additional post in front of the spur, to add more options when tuning the chassis’ flex. By installing or removing the flanged bearings either side of the spur gear, owners can change the flex point of the car instantly, either moving it forwards or backwards to adjust the balance of the car.

Continue reading here

January 23, 2020

RC Maker T4’20 carbon fibre floating electronics plate

RC Maker have introduced their Xray T4 2020 floating electronics weight plate in a carbon fibre variant. Weighing in at 12g for the set, 10g of that being close to the centre of the chassis with 2g being the carbon plate, the set is adding minimal weight to the motor side of the chassis. The plate attaches to the often unused antenna mount hole but if owners still want to use this antenna mount, they can use an extra long screw through the lower weight, and thread the antenna mount on-top. Another added bonus is that the construction makes it easy to change chassis or clean the car as the receiver, transponder and fan are simply extracted by undoing one screw.

View more images here

January 20, 2020

RC Maker T4’20 GeoCarbon shock towers

Coming from RC Maker are new GeoCarbon series shock towers for the Xray T4 2020 mid-motor touring car. Available for the front and rear of the car, the shock towers feature a dual-sided GeoCarbon finish and they are 3mm thick with a re-designed profile to introduce a marginal amount of flex, giving the car more traction, which is very often highly favourable for all asphalt racing, as well as low-medium traction carpet tracks. The towers are available mimicking the standard shock geometry and they also come as -3mm variant, allowing to access the new lower A-arm shock mounting position that can be an advantage in higher grip track conditions.

View the other new shock towers here

January 16, 2020

RC Maker BD10 GeoCarbon bumper plate & battery brace

RC Maker have introduced new GeoCarbon carbon fibre optionals for the Yokomo BD10 touring car. First up is a bumper plate with stopper that sports a stylish, stealth and innovative design. This support contacts the bulkheads and prevents impacts from snapping the main chassis and are very important. The design includes a 5mm brace which sits below the plate, raising it to the correct height and significantly increasing the strength of the whole assembly. Upon resting, there is a 0.2mm gap between the bulkheads and the support, to prevent any rubbing and tweaking. This support will only be active in a crash. This provides the optimal solution to keeping the chassis on the brand new BD10 safe, whilst looking great at the same time.

Continue reading here

December 30, 2019

RC Maker T4’20 floating electronics weight plate

RC Maker have introduced their new floating electronics weight plate for the Xray T4 2020 touring car. The plate puts weight where it is needed most, to get the car up to he minimum weight and balanced. The set includes a carbon shim which floats it 0.5mm off the chassis from near to the centre of the car, meaning the plate itself has minimal to no impact on the flex of the chassis. On top of the plate, there is a 10g of brass weight to secure it in place. The plate attaches to the often unused antenna mount hole. If drivers still want to use this antenna mount, they can use an extra long screw through the lower weight, and thread the antenna mount on-top. The plate itself is 1mm thick and weighs in at 12g. The set coming in at 22g is a brilliant way to meet the limit, balance the car and have no impact on the flex characteristics of the chassis at the same time. Another added bonus, is owners can change chassis or clean the car, and simply remove the receiver, transponder and fan simply by undoing one screw. If drivers are after more weight for the car, RC Maker have a 1.5mm option plate available weighing in at 20g which can either replace the 1mm plate to bring the overall weight up to 30g, or added to the 1mm plate to make a total of 2.5mm, bringing it all the way up to 42g. The set comes packaged in a high quality black magnetic lid box with RC Maker logo on a clear front window, ensuring the plate is kept in perfect condition in transit.

View more images here