Red RC » RC Maker

January 21, 2019

RC Maker Geo carbon wing endplates

RC Maker have introduced their brand new Geo carbon wing endplates for 1/10th touring cars. Light weight and durable, they give a body the ultimate sexy look. Machined pockets give the end plate a 3D geometric look, whilst also maintaining strength and they are meant to increase the car’s stability all round, especially on the straight. The set includes two pairs of endplates that fit most 1/10th touring car rear wings. Please note that some tracks and racing series do not allow the use of carbon fibre parts on the body shells or wings – be sure to check with the organisers before using them.

View the mounted endplate here

January 16, 2019

RC Maker A800X centre weight spacer

RC Maker have introduced their new centre weight spacer for all rear motor Awesomatix A800X cars. This 0.5mm carbon plate makes it very easy to lift the centre weight on the A800X. Normally shims are required which are very fiddly and difficult to install, this plate does not require the screws to be undone fully and slides in from the side, making it a super adjustable and easy solution.

View another image here

January 15, 2019

RC Maker TC bellcrank ackermann shim plates

New from RC Maker are these simple ackermann plates which slide into the bell crank steering on most cars and allow to change the ackermann geometry without totally unscrewing the ball studs to install a shim, which can be a fiddly job. They install by simply loosening the ball studs and sliding the plates in or out and tightening. The set consists of two plates, one 0.5mm and one 1mm, allowing to tune your the steering ackermann from 0.5-1.5mm in 0.5mm increments. These fit the Xray T4, Yokomo BD9, Infinity IF14, Awesomatix A800X, ARC R11 and any other car with bell crank ballstud spacing of 8.0-8.5mm.

View more images here

December 15, 2018

RC Maker body shell anti-tuck wing mount set

New from RC Maker is an anti-tuck system for touring car body shells. Mounting between the wing strut and behind the lower wheel arch, they add significant stability to the rear of the body shell and prevent body tucks during racing, and unwanted vibrations on large tracks. The set is developed together with experienced Australian 3D printing company Think RC, and has been rigorously durability tested on track. Weighing in at only 7g for the pair and removing the need for a wing nut, they are a very viable option for all levels of drivers, and also a great, constructive way of adding weight for the ETS 90g rule. Moulding perfectly to the wing strut, they also feature a rear strut support which braces the back of the strut where damage from crashes is normally unable to be repaired. They are currently available for Protoform Type S and D9 bodies.

View more images here

November 22, 2018

RC Maker carbon chassis balancing tool

New from RC Maker is this lightweight, low profile set of balancing blocks, designed to locate into the small hole/dimple in the bottom of Touring Cars and 1/12th Pan Cars chassis. Taking on a different form to traditional balancing blocks, it more easily slides under the chassis thanks to the long carbon arm. The low friction ceramic silicon nitride ball ensures minimal friction with the chassis, ensuring you can accurately see the balance of your car. The blocks come as a pair, one for the front and rear of the chassis.

Source: RC Maker [rcmaker.com.au]

November 9, 2018

RC Maker double-sided setup board

New from RC Maker is their premium double-sided setup board. It features a super flat, lightweight construction, with a high-quality solvent-resistant print. The print is double sided, with horizontal and vertical designs on each side fitting every racers preference. It comes packaged inside a matching bubble pouch to protect it during travelling.

View another image here

November 1, 2018

RC Maker Ultimate carbon setup station & parts tray

New from RC Maker is an all-in-one carbon fibre parts tray. It manages to integrate a setup station holder and parts tray all in one, providing a very lightweight and compact solution to keeping your pit table clean and tidy. It is made of the highest quality 3mm carbon fibre, and features a screw together construction, which allows disassembly for cleaning and easy customisation of the screw colours to suit your look. The frame holder suits Hudy and Arrowmax setup stations, it incorporates a toe plate holder, setup wheel nut holder, four micro magnets to hold body clips, wrenches and accessories while four large pockets allow to separate screws, shims nuts and parts.

View more images here

August 21, 2018

RC Maker carbon charger & power supply stand

New from RC Maker is a simple and versatile carbon fibre charger and power supply stand. It features a slot together, compact footprint and is constructed from high quality 3mm carbon fibre. The stand itself is very sturdy, and made sturdier by holding the power supply underneath, which stabilises the whole unit. Increasing the room on your pit table, it also allows for more ventilation for the charger and power supply, allowing them to run cooler and more efficient. It sports two different width settings to house the smallest chargers – such as the iCharger X6 – right through to the bigger range of iChargers and other brands.

View more images here