Red RC » Short Course

November 8, 2019

RPM Tenacity SCT/DB/T chassis skid plates

Coming from RPM is a new skid plate set for the Losi Tenacity SCT, DB and T vehicles that helps to bulletproof the popular trucks. The front and rear skid plates are designed to fit both the moulded chassis version of the Tenacity as well as the aluminium chassis option. A key breakage area of the moulded Tenacity chassis is the area located just behind the front bulkhead mounting screws. By tying together the four bulkhead mounting screws with the two screws holding the steering mounting posts in place, the plate beefs up the strength and durability of the entire front end of the chassis, helping to reduce that pesky breakage problem while adding some much needed abrasion resistance to the chassis. As for the aluminium chassis, the skid plates will not only increase the longevity of the valuable alloy main plate, they will also significantly reduce the amount of scuffs and scratches it will receive since the skid plates are the lowest impact point on the chassis. Out back, the rear skid plate adds some much needed abrasion and wear protection for both the moulded composite and aluminium chassis. Drivers will also encounter less build-up of dirt and debris between the chassis and the lower rear bumper mount since the rear skid plate sits lower than the bumper mount. Both the front and rear skid plate are moulded from high-quality nylon material for durability and they come including mounting hardware.

View more images here

November 1, 2019

Exotek release new fan mount accessories

Exotek have introduced several new accessories to make fan mounting easier. First up is the V2 variant of the company’s popular 1/8 Exo fan mount that features a larger double screw mounting bar. The mount allows to attach optional high powered 40mm and 30mm fans as the mounting bracket has multi-mount features that allows the fan to be securely affixed to the motor can in tight spaces. The extra modular design means with a few adjustments owners can mount a fan securely in any 1/8th scale truggy and most E-buggies and the mount positions the fans 10mm to 14mm away from the motor can. This proper spacing helps insure the fan does not lose power due to magnetic interference from the motor. A fan that is placed too close to the motor can actually stop spinning as the driver applies maximum throttle due to the fact that the motors stronger EMF can slow or shut down the fans EMF. The mount was designed for the use with high power 40mm and 30mm fans and standard 1/8th scale motors with 39.5mm to 40.5mm diameter and it comes in polished and anodised black or blue for a factory look.

Continue reading here

October 31, 2019

JConcepts Fling King SCT tractor tyres

JConcepts have introduced their new Fling King SCT tractor tyres that are specifically designed to throw mud, dirt, gravel and grass just like the real thing. The giant-sized tyres are tall enough to dance through the deepest RC loam, however, its the tall lugs that separate them from the rest. Full-scale tyres like these are hand-cut to produce the most wicked looking tyres on the block. The JConcepts tyres are uniquely built to replicate a hand-cut set, however, deep tread remains to do the “mega” land damage the drivers and enthusiasts crave. One of the details about the SCT Fling Kings, they are designed for 3.0 x 2.2” standard SCT wheels, making them even more appealing. No details were spared on these mud runners, the V-type tread is replicated to a T and the top of the tread carries a slight recess adding a little touch of depth to the appearance. Off to the side, the tire lettering hits hard with retro style JConcepts lettering and Fling King logo. The super soft “green” compound which is recommended for dirt, grass and asphalt feels noticeably sticky and has expanding characteristics during flat out high-speed runs. The tyres include the Dirt-Tech closed cell inserts and they mount directly to Hustle, Hazard and Rulux 3.0 x 2.2” wheels which feature 12mm hex mounting capability for a vast assortment of SCT trucks on the market.

Source: JConcepts [jconcepts.net]

October 30, 2019

JConcepts NCTS Rd4 Midwest Carpet Nats – Report

The final round of the inaugural JConcepts NCTS was held at Thunder Road RC Raceway in Waite Park, Minnesota over the weekend. The popularity of carpet and turf racing is definitely on the rise and without any doubts whatsoever, racing on artificial surfaces is clean, consistent, and drivers always have a good amount of grip. As the NCTS season 1 comes to an end, the organisers are convinced that the carpet wave will carry strong into 2020 and beyond. For the season finale, the hype was high as many of the team drivers have been raving about the facility and they are completely right. The layout was actually very cool. It was a reflection of itself if you were to split it down the middle. With the jumps and features laid out in a manner that challenged drivers, it wasn’t an easy track to get around going 100 precent. However, cruise around at 80 percent, it was very easy. The double vertical chicanes haven’t been done in a while, but definitely, required precision and commitment to get the hot laps. The jumps were quite easy, which promoted close racing and many laps of battling on the track that ultimately made for a wonderful race experience. Overall, it was a fun layout that favoured cars with balanced setups that inspired confidence and control.

Continue reading the report here

October 24, 2019

Sunpadow Phantom II Black Label LiPo packs

Sunpadow have announced the release of their new Phantom II Black Label competition LiPo battery range. Listening to the feedback of their factory drivers, the packs utilise a new technology and production process, making for improved performance while being more cost efficient for the customer at the same time. The range includes standard and shorty options with the standard size range coming as 8800mAh (25.1mm/308g), 6600mAh (23.1mm/312g), 6300mAh (23.1mm/288g), 6000mAh (23.1mm/295g), and 5600mAh (23.1mm/277g) variants. The shorty batteries are available as 2S 5100mAh (25.1mm/215g), 4500mAh (25.1mm/214g) and 4000mAh (18.5mm/157g) options and also as 8000mAh (18.5mm/155g) 1S 1/12th scale battery. All feature black hardcases with black labels and they come in zipped storage containers.

Source: Sunpadow [sunpadow.com]

October 23, 2019

2019 The Dirt Buggyland Challenge – Announcement

The 2019 The Dirt Buggyland Challenge will be held November 22nd to 24th at Thunder Alley Raceway in Beaumont, California. The event brings together two icons of 1/8th off-road racing in the form of Joey Christensen’s The Dirt Racing and the Spanish Buggyland crew and it will see the running of Pro, Sportsman and Intermediate Nitro and Electric Buggy and Truggy classes as well as a single Short Course Truck category. There will be practice on Friday with racing on Saturday and Sunday. Included in the event are fun and challenging “racer games” such as a foot race, mechanics as drivers race along with a few more surprises. Many of USA’s top professionals will be in attendance including Jared Tebo, Cole Ogden, Joe Bornhorst, Adam Drake, Ryan Cavalieri and more. That all is happening on a brand new track designed and built by both The Dirt Racing and the Buggyland creator Miguel. More information and sign-up can be found here.

October 22, 2019

Inaugural BKlassic Race – Report

Hobby Action Raceway of Chandler, Arizona held the inaugural BK Race this past weekend. Brian Kinwald was a special individual. He lived and breathed RC and at a young age, showed the world that he was not like any other racer on this planet by winning the IFMAR World Championships in Basildon, England, in 1993. That was his first WC title and in 1997, Brian went on to win it again, but this time for Team Losi Racing. With two WC titles and a ton of National titles under his belt, Brian is undoubtedly considered one of the best to hold a radio. But what is truly special about Brian Kinwald is the influence he had on young racers back then and for many decades to come. Unfortunately, the news of Brian passing earlier this year was felt throughout the entire industry.

Continue reading the report here

October 22, 2019

Pro-Line Reaction HP SC 2.2”/3.0” belted drag racing tyre

Made for the popular no-prep drag racing are Pro-Line’s new Reaction HP SC 2.2”/3.0” belted tyres. Featuring an inner belt reinforcement the tyres will not balloon or expand during use, which will give drivers maximum control to put the power down. They are made of Pro-Line’s popular soft S3 compound for lots of grip and they come including foam inserts and are usable with standard 2.2”/3.0” short course truck wheels. Designed for drag racing they however have a 90 mph or about 7,000RPM speed limit to ensure the inner belt will not become damaged due to excessive speeds.

View another image here