Red RC » RC Maker

May 6, 2019

RC Maker GeoCarbon touring car tweak wheel set

RC Maker have introduced their all-new GeoCarbon tweak wheel set for EP and GP touring cars. The super lightweight wheels weight in at only 2.2g each and are precision machined to minimum tolerances to help de-tweak the car. Consisting of a less than half of a normal setup wheel construction, they serve the purpose of checking the tweak via lifting the chassis off the ground at one end only, and making sure the wheels leave the ground at the same point, being an extremely common way to de-tweak an on-road car. Using precision machined parts is far more accurate than using a normal wheel and tyre, and more accurate than a normal rubber O-ringed setup wheel. Having no buffer between the wheel and ground makes it far easier to feel when one wheel is lifting up earlier, as drivers can feel the abrupt bump on the setup board. This leads to more accurate and faster setting of tweak.

View another image here

April 26, 2019

RC Maker A800 long arm roll centre shim plate set

Coming from RC Maker is a new roll centre shim plate set for A800 cars using the optional long arms. Consisting of two different thicknesses of 0.5 and 1mm, the set allows tuning from 0.5 to 1.5mm which covers the normal range for Awesomatix cars. The plates also have a front and a rear, with cutouts to distinguish them, due to the hole spacing being wider in the front. They slide in without the removal of your screw, allowing to slide out the old and in the new in a matter of seconds. Once the plate is installed simply tighten as normal. The plates work in the outer as well as the inner positions and the central hole allows easy removal by inserting a 1.5mm driver and sliding them out from the top. The shims are only usable on A800 cars using the LA +9.0 and +8.0 arms and the set includes four 0.5mm and four 1.0mm thickness shims.

View another image here

April 23, 2019

RC Maker Awesomatix GeoCarbon battery mount set

RC Maker have introduced their new GeoCarbon series battery mount set for the Awesomatix A700 and A800 touring cars. A direct replacement for the Awesomatix P23 and AM12X parts the set is 50 percent lighter at only 0.8g each and the set includes 3mm spacers to raise the hook to increase support and prevent scratching on asphalt. The parts are machined from high-quality glossy finish 3K 3mm carbon fibre and they are highly adjustable for different batteries and battery positions.

View more images here

April 18, 2019

RC Maker Awesomatix GeoCarbon front bumper mount

RC Maker have introduced the next instalment in their GeoCarbon range, the GeoCarbon front bumper mount for the Awesomatix range of touring cars. Designed to be used with the kit P14-1X lower bumper mount, it increases the bumper’s rigidity, and also the body post rigidity by offering more support around the post. This is a direct replacement for the standard part, and also includes an additional brace to brace the bumper to the bulkheads, preventing the bumper from bending in impacts. This part does not touch the bulkheads but clears by the slightest of margins as to ensure no tweaking. Constructed of high-quality 3K 3mm carbon, it is lightweight and durable, and also super sexy.

View more images here

February 14, 2019

RC Maker touring car floating electronics plates

RC Maker have introduced their new adjustable electronics mounting plates for most of today’s 1/10th electric touring cars. The floating brass mount with central attachment allows for fully floating electronics with absolutely minimal flex interference, giving symmetrical flex, which is not possible in conventional layouts. The plates make it incredibly easy to swap chassis plates, as electronics stay fixed to the plate, making it only two screws to swap all electronics over, without messing with tape. The unique design is making it very easy to swap between chassis manufacturers and try different plates all without having to buy entire new kits while offering left-to-right chassis balance adjustment. Different fastening inserts allow for even greater versatility without the need to buy a whole new set again. Same with changing to different plates and centre weights, they are all compatible with each-other. Beside the double-sided design, RC Maker also offers a single sided set with 4mm of adjustability left and right to adjust the balance bias of the car. Used for the electronics only it allows to tune the chassis balance, and also move weight in or out both sides to adjust the amount of roll in the chassis depending on the traction level. In addition to the brass double and single-sided sets, RC Maker also offer the brass plates separately to conversion double into single and single into double-sided designs. Optional carbon fibre option plates make for reduced overall mass if needed while an optional +10g centre weight adds further weight tuning options. Supported cars include the Yokomo BD8 and BD9, Xray T4 2017 to 2019, Team Associated TC7.1 and TC7.2, Tamiya TRF419X, Awesomatix A800X, Infinity IF14, Xpress XQ1, Mugen MTC1 and ARC R11’19.

View more images here

January 30, 2019

RC Maker Geo carbon wheel arch and skirt tool

New to RC Maker’s new Geo Carbon range of products, is this unique wheel arch tool, which not only gives a template for the body’s wheel arches, but also sets the skirt height for the body based off axle height. After locating the axle with the body mounted, modellers can simply trace around the entire carbon fibre template, which provides both a wheel arch line and a skirt cutting line. The template also features an elongated slot unlike its predecessor, allowing to accurately offset the wheel arch to prevent tucking in the rear of the wheel.

View more images here

January 21, 2019

RC Maker Geo carbon wing endplates

RC Maker have introduced their brand new Geo carbon wing endplates for 1/10th touring cars. Light weight and durable, they give a body the ultimate sexy look. Machined pockets give the end plate a 3D geometric look, whilst also maintaining strength and they are meant to increase the car’s stability all round, especially on the straight. The set includes two pairs of endplates that fit most 1/10th touring car rear wings. Please note that some tracks and racing series do not allow the use of carbon fibre parts on the body shells or wings – be sure to check with the organisers before using them.

View the mounted endplate here

January 16, 2019

RC Maker A800X centre weight spacer

RC Maker have introduced their new centre weight spacer for all rear motor Awesomatix A800X cars. This 0.5mm carbon plate makes it very easy to lift the centre weight on the A800X. Normally shims are required which are very fiddly and difficult to install, this plate does not require the screws to be undone fully and slides in from the side, making it a super adjustable and easy solution.

View another image here