Red RC » P On Road

June 8, 2016

Eduardo Escandón sweeps Modified class at SNS Rd3

The recent third round of the Spanish National Series saw Eduardo Escandón (Yokomo) taking the TQ honours in the Touring Modified class. Setting a new fastest lap and track record, the nitro on-road expert left David Pérez (Xray) behind in second place while Gonzalo García (Yokomo) rounded out the top 3 after the five rounds of qualifying. The opening A-main on Sunday then saw David taking the win from Edu as the latter ran into problems. Beto Rivera (Xray) completed the top 3 in A1. The next two A-mains then had Edu dominating the proceedings, taking convincing wins in both legs to take the overall win from David Pérez and Beto Rivera.

Source: SNS [snseries.com]

June 8, 2016

SRP 6000mAh Stock Spec LiPo battery

SRP Quality Products have introduced their new 6000mAh 100C Stock Spec LiPo battery pack. Specially developed for stock racing classes the 2S hardcase battery utilises 100C high-performance cells with a low internal resistance and a flat discharge curve for maximum power over the whole run. The pack weighs in at 295g, it makes use of standard 4mm connectors and comes including a pre-wired balancer wire with XH balancer and Deans-type power connectors.

Source: SRP [srpqualityproducts.com]

June 8, 2016

Mario Spiniello takes Italian 200mm title

The iconic Gubbio track recently played host to the 2016 Italian 1/10th 200mm nitro championships. In the main final Mario Spiniello (Xray) took the win after a flawless race that saw Mario making a super-fast tyre pitstop that promoted him into the 1st place around the 25 minute mark. In the closing stages Mario only had to control a 3-second gap to teammate David Loppini (Xray) who was on a different fuel strategy with one additional pitstop. Behind the two Dario Balestri (Capricorn) completed the podium result in third.

View the final results here

June 8, 2016

Chicha Rioja wins at Spanish National Series Rd3

The third round of the Spanish National Series was held at the Club Automobilismo Gijon in the North of the country. In the Touring Stock class Rafael Ortiz (ARC) would grab a very narrow TQ from Chicha Rioja (Yokomo) who was only 0.03 seconds behind. The entertaining triple A-mains saw Chicha taking the win in A1, a fourth place in A2 and the runner-up spot in A3 but overall he would walk away with the win from pole position holder Rafael while Tony Mur (Xray) completed the top 3 result.

Thanks to Edgar Schultz for the report.

June 8, 2016

Jonnhy Pastor wins at Spanish 200mm Touring regionals

The recent Spanish 1/10th 200mm Nitro Touring regionals saw Mugen’s Jonnhy Pastor walking away with the win. Starting from the 2 spot into the A-main Jonnhy put his car in the lead already in the second corner only to loose it some five or six laps later due to clutch problems. But after the first round of pit stops Jonnhy was back in third and soon after he was also promoted into second, allowing him to challenge team mate David Belen (mugen). The latter later suffered car problems so he was out of the race for the win. Raul Amella (Xray), also in the mix for the win, had to cope with a flame out before refuelling, giving Jonnhy room to breathe and to cruise to the win from David and Raul.

View the top 3 result here

June 7, 2016

Xray NT1 rear graphite chassis stiffener

Coming from Xray and made for the NT1 1/10th 200mm nitro on-road car is a rear graphite chassis stiffener. Designed to eliminate flex around the engine area the brace comes in handy especially on high-bite tracks as it couples the radio plate mount and the 2-speed bulkhead, resulting in a reinforced rear chassis section. Included with the stiffener comes suitable mounting hardware.

Source: Xray [teamxray.com]

June 7, 2016

Brilliant RC C-18 R 1/8th scale on-road bodyshell

Brilliant RC have introduced their new C-18 R 1/8th scale on-road bodyshell. Available in a standard non-cut but also pre-cut variants for vehicles such as the Shepherd Velox V8, Mugen MRX-6, Serpent 977, Xray RX8 and ARC R8.0, the body is manufactured in Germany from finest 0.75mm polycarbonate with well distributed material thickness making for best durability and performance. The body’s shape ensures a very good overall traction in combination with a lot of steering, resulting in a super smooth but fast handling. Coming with window masking sheet and decals, the EFRA homologated body (#31545) will also be legal for the Pro Stock Series and it is available very soon.

View more images here

June 7, 2016

T-Works tyre additive bottle

T-Works tyre additive bottle-2

T-Works have introduced their new tyre additive bottle with heavy duty applicator. The sponge applicator will withstand even highly aggressive traction sauces such as the Mighty Gripper V3 with the 50ml bottles being ideal to mix own additives or to control the amount of sauce taken with you during travelling. Included with the bottle comes a range of coloured dots to allow for easy marking.

<View another image here